Spoke Count & Rider Weight
#1
Member
Thread Starter
Join Date: Nov 2002
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Spoke Count & Rider Weight
Here's a question for the better informed. Since the advent of low spoke count wheels, I keep reading about weight limits associated with them. However, whenever I visit a manufacturer's site, I never see any recommended weight range given for their wheels. I've also never read any postings that explicitly mentioned actual numbers... I need quantitative data, please.
Is there a general rule or formula for weight and spoke count?
My current bike came with 24R/20F spoked wheels. Works fine, but occasionally when I make a quick correction at high speed, it doesn't feel as sure-footed as my previous 32R/32F wheels. So I am curious if I am bumping up on the recommended limit on these things.
Is there a general rule or formula for weight and spoke count?
My current bike came with 24R/20F spoked wheels. Works fine, but occasionally when I make a quick correction at high speed, it doesn't feel as sure-footed as my previous 32R/32F wheels. So I am curious if I am bumping up on the recommended limit on these things.
#2
Banned
Join Date: Aug 2001
Location: upstate New York
Posts: 1,688
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Weight limits for a wheel with a certain number of spokes depends mostly on the gauge of the spoke, also the material that the spoke is made out of, as well as the type of spoke (straight, butted, bladed, swaged, etc.). Also, the pullout strength of the holes on the flange are a consideration, but these are usually higher than the failure strength of the spoke (unless, of course, you do something inadviseable, such as radially lace a high-flange hub...) Because of all these different concerns, it is d@mn hard to make any generalisation based solely on spoke count.
As far as manufacturers specs are concerned, yes, they all have maximum limits determined by the builder. Maybe you should e-mail the manufacturers that you are interested in.
As far as manufacturers specs are concerned, yes, they all have maximum limits determined by the builder. Maybe you should e-mail the manufacturers that you are interested in.
__________________
Je vais à vélo, donc je suis!
Je vais à vélo, donc je suis!
#3
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,807
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1394 Post(s)
Liked 1,335 Times
in
841 Posts
Sorry, I do not care for low spoke count wheels. Perhaps a racer can justify the reduced air drag/turbulence, but I want strong, reliable, light wheels, and basic physics tells us, "the higher the spoke count, the better the strength-to-weight ratio." Also, a rim with a high spoke count is amenable to accurate truing. I have 32-spoke wheels on the Bianchi and son #2's mountain bike, and 36-spoke wheels on everything else.
... proud to be a retrogrouch ...
... proud to be a retrogrouch ...
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#4
Member
Thread Starter
Join Date: Nov 2002
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
What can I say? The bike came with them. I was surprised to find out that 20-24 spoke wheels aren't the rock bottom (still don't see how 16 spokes can hold a wheel together). In any case, if anything happens to these wheels, I'll probably go back to 32.
However, I have rode over more than a few hard bumps at high speeds, and they stayed true. So they're not as fragile as I first thought.
However, I have rode over more than a few hard bumps at high speeds, and they stayed true. So they're not as fragile as I first thought.
#5
Junior Member
Join Date: Jan 2003
Posts: 11
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have been using Rolf Vector COMP wheels for the past year. I weigh about 70 kg(155 pounds) and have had absolutely no problem with them.
Both front and rear wheels have 18 flat spokes. I have been over a couple of harsh bumps with them and have not had to true them even once. Response wise they are perfect. I would really like to try the other wheels in the Rolf range.
Both front and rear wheels have 18 flat spokes. I have been over a couple of harsh bumps with them and have not had to true them even once. Response wise they are perfect. I would really like to try the other wheels in the Rolf range.
#6
Senior Member
Join Date: Dec 2002
Location: Texas
Posts: 102
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
I recently purchased a Raliegh Competition with the Shimano 540 wheels. These wheels have 16 bladed spokes front and rear. In researching any weight limitations for these in the spec/instruction sheets provided with the bike there is absolutely no mention of weight restriction. I guess my take on the weight issue would be that if there was an issue the manufacture would be liable at the very least be obligated to note such with the supplied paperwork. In lieu of of the silence in their supplied paperwork I beleive they are stating (indirectly) that there are NO such limitations. (IMHO)
My mountain bike has 32 spokes and quite frankly I can not tell any differerence in road feel/performance between the two. Obviously I don't take my road bike off the tarmac but having riddden both bikes on the same road route I normally utilize I beleive the comparsion is valid.
While I am not an engineer I don't necessarily subscribe to the "more is stronger" theory. I believe with the right mix of materials (metals) and design that you can accomplish the same, if not more, with less. (again IMHO)
My mountain bike has 32 spokes and quite frankly I can not tell any differerence in road feel/performance between the two. Obviously I don't take my road bike off the tarmac but having riddden both bikes on the same road route I normally utilize I beleive the comparsion is valid.
While I am not an engineer I don't necessarily subscribe to the "more is stronger" theory. I believe with the right mix of materials (metals) and design that you can accomplish the same, if not more, with less. (again IMHO)
#7
Just ride.
Can't answer your question, but had some comments. There are other things that affect feel & performance... it's not clear what you mean by "quick correction". The low spoke wheels are almost always radially spoked, some people complain about wind-up under hard acceleration.
Where are you reading about weight limits?
Seems to me that for weight limit information to be meaningful, it has to be surrounded with a bunch of other specs. Like maximum sprint torque, deepest pothole @ x velocity, etc.
Originally posted by rchan
I keep reading about weight limits associated with them. However, whenever I visit a manufacturer's site, I never see any recommended weight range given for their wheels.
I keep reading about weight limits associated with them. However, whenever I visit a manufacturer's site, I never see any recommended weight range given for their wheels.
Seems to me that for weight limit information to be meaningful, it has to be surrounded with a bunch of other specs. Like maximum sprint torque, deepest pothole @ x velocity, etc.
#8
Member
Join Date: Dec 2002
Location: Sydney Australia
Posts: 34
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
i weigh about 85kg (187lb) and i have a set of shimano dura ace wheels on my bike. 16 flat spokes and have not had any problems whatsoever. the manufacturers claim that they are very stiff because of the spokes being anchored on the opposite side to where they are started from.
Eg. they are on the left hand side of the hub and they cross over to be anchored on the right hand side of the rim. i dont know how good their theory is but it better be good because i paid good money for them. eheheheh
slick1
Eg. they are on the left hand side of the hub and they cross over to be anchored on the right hand side of the rim. i dont know how good their theory is but it better be good because i paid good money for them. eheheheh
slick1
#9
Member
Thread Starter
Join Date: Nov 2002
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Originally posted by roadbuzz
Can't answer your question, but had some comments. There are other things that affect feel & performance... it's not clear what you mean by "quick correction". The low spoke wheels are almost always radially spoked, some people complain about wind-up under hard acceleration.
Where are you reading about weight limits?
Seems to me that for weight limit information to be meaningful, it has to be surrounded with a bunch of other specs. Like maximum sprint torque, deepest pothole @ x velocity, etc.
Can't answer your question, but had some comments. There are other things that affect feel & performance... it's not clear what you mean by "quick correction". The low spoke wheels are almost always radially spoked, some people complain about wind-up under hard acceleration.
Where are you reading about weight limits?
Seems to me that for weight limit information to be meaningful, it has to be surrounded with a bunch of other specs. Like maximum sprint torque, deepest pothole @ x velocity, etc.
As to where I've read stuff about weight limits, I can't remember any 'official article', always some anecdotal comment about 'I'm only X lbs., so the wheels are fine, but might not be for a heavy rider.' Very vague qualitative statements, so I just wanted to know if there was something to it. Very little hard facts as far as I know.
#10
Just ride.
Originally posted by rchan
Trying to describe what one 'feels' on a bike is much like people describing wine... 'astringent yet nutty' or something like that. I see a pothole at the last second and jerk a bit to avoid it; yeah, I shouldn't do that, but it gets dark in the winter. Doesn't feel the same as with my old wheels. I guess I don't have the proper vocabulary to tell you what I mean.
Trying to describe what one 'feels' on a bike is much like people describing wine... 'astringent yet nutty' or something like that. I see a pothole at the last second and jerk a bit to avoid it; yeah, I shouldn't do that, but it gets dark in the winter. Doesn't feel the same as with my old wheels. I guess I don't have the proper vocabulary to tell you what I mean.
As to where I've read stuff about weight limits, I can't remember any 'official article', always some anecdotal comment about 'I'm only X lbs., so the wheels are fine, but might not be for a heavy rider.' Very vague qualitative statements, so I just wanted to know if there was something to it. Very little hard facts as far as I know.
That said, I'm sure they have their limits, but unless you're a pretty hefty guy, they're probably okay. Quit worrying about your wheels, and find some better wine!
#11
riding a Pinarello Prince
Join Date: Jul 2000
Location: Downtown Toronto,Canada
Posts: 2,409
Bikes: Pinarello, Prince and an FP5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I guess I will not have a problem with my wheels, I am using a Mavice Cosmic Elite, and I weight 165 lbs. Have looked at my wheels even when I have had a bad fall it is still very round and even.
__________________
"Racso", the well oiled machine;)
"Racso", the well oiled machine;)
#12
1.64x10^6 posts
Join Date: Aug 2002
Location: Spring, TX
Posts: 501
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The only place I've found specs for rider weight limits is here, but I suspect these limits are intended to apply only to their buildups and not a general guide.