LBS "tightened" my crank, but it's loose again and clanking
#1
Senior Member
Thread Starter
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,552
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,582 Times
in
2,343 Posts
LBS "tightened" my crank, but it's loose again and clanking
I gad some play in my crank and so I brought it in to my LBS. I also had chain hop and a new chain didn't fix it so I had them swap in a new rear cog. I had asked them to 'service" my crank and mentioned grease. When I picked it up they said all it needed was to be tightened. I rode it 5 miles and it is making God-aweful clanking sounds and is loose again. (btw - it was fine when I test rod eit outside the shop)
what the heck is clanking?
do I take it back to this shop or go to another?
what the heck is clanking?
do I take it back to this shop or go to another?
#2
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
If it's a "square taper" crank and you rode it while it was loose, you may have damaged the crank to the point where it will never stay tight again.
Aluminum square taper cranks have to be a very tight fit on the hard steel bottom bracket spindle and the recommended installation torque is very high. If the cranks get loose for what ever reason, usually because they weren't installed properly to begin with, the steel spindle will distort and damage the hole in the crank so that it will never fit properly again.
If that's the case, your only option is a new crank.
Aluminum square taper cranks have to be a very tight fit on the hard steel bottom bracket spindle and the recommended installation torque is very high. If the cranks get loose for what ever reason, usually because they weren't installed properly to begin with, the steel spindle will distort and damage the hole in the crank so that it will never fit properly again.
If that's the case, your only option is a new crank.
#3
Member
Join Date: Aug 2009
Location: Leeds
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
[QUOTE=HillRider;9495868]
If it's a "square taper" crank and you rode it while it was loose, you may have damaged the crank to the point where it will never stay tight again.
/QUOTE]
Hi
That sounds like my problem with my daughters bike, pedal comes loose and the centre nut holding it in place loosens too. Tightened it a few times, but the same thing happens.
On inspecting the bolt, the first quarter of the thread is stripped. Maybe a new bolt will solve the problem.
G
If it's a "square taper" crank and you rode it while it was loose, you may have damaged the crank to the point where it will never stay tight again.
/QUOTE]
Hi
That sounds like my problem with my daughters bike, pedal comes loose and the centre nut holding it in place loosens too. Tightened it a few times, but the same thing happens.
On inspecting the bolt, the first quarter of the thread is stripped. Maybe a new bolt will solve the problem.
G
#4
Senior Member
Join Date: Jul 2009
Posts: 164
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If it's a cheap, old bike and you don't want to spend money on it.....take crank off and try tapping
(alright, hammering - gently) the inner face of the crank around the axle hole. This may take some time/trial and error, but it can work if you're desperate. I've done it in the past a couple of times but not with a decent/expensive bike !
(alright, hammering - gently) the inner face of the crank around the axle hole. This may take some time/trial and error, but it can work if you're desperate. I've done it in the past a couple of times but not with a decent/expensive bike !
#5
cab horn
Join Date: Jun 2004
Location: Toronto
Posts: 28,353
Bikes: 1987 Bianchi Campione
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 26 Times
in
19 Posts
It's a dilemma. On the one hand, the shop which carried out the work should be compelled to do it properly. On the other, you may be reluctant to entrust it to them again. I incline toward the latter course, but I do my own work anyway, and it's hard to imagine yourself being dependent on other people (which I guess I would be if this computer went AWOL). Your call. If you decide they should put it right, ask to speak to the shop owner or manager. Say as little as possible, after explaining what you requested to be done and the present outcome. Sometimes, we put ourselves at a disadvantage in these situations by talking too much to cover our discomfiture, and predatory merchants sense this. If you know any outlaw bikers, it wouldn't hurt to take them along as well, just for a bit of background menace. Tattoos are good.
What's clanking is probably one of the cranks, which is loose on its taper. If it were mine, I'd feel happier if the entire bottom bracket were taken apart and regreased, so the balls and races can be checked - unless it's a sealed one, naturally.
What's clanking is probably one of the cranks, which is loose on its taper. If it were mine, I'd feel happier if the entire bottom bracket were taken apart and regreased, so the balls and races can be checked - unless it's a sealed one, naturally.
Give me a ****ing break.
#6
Senior Member
If you've got damaged crankarms from riding it previously when it was loose, most likely there's absolutely nothing the shoppe can do to fix it for you. You'll need to buy a new crankarm.