Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Removing Chrome

Search
Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Removing Chrome

Thread Tools
 
Search this Thread
 
Old 12-08-09 | 04:55 PM
  #1  
Thread Starter
Junior Member
 
Joined: Nov 2009
Posts: 11
Likes: 0
Removing Chrome

Hi Guys

i have a dmr sidekick frame as shown below:



i would like to remove the (what appears to be chrome) paint from the frame

basically i want to take it back to bare metal in order to then respray.

i considered getting it shot blasted

has any body else had experience simlar to this and how did they remove the paint

thanks
t_dubz is offline  
Reply
Old 12-08-09 | 05:10 PM
  #2  
KDC1956's Avatar
Senior Member
 
Joined: Mar 2009
Posts: 671
Likes: 1
From: Arkansas

Bikes: Surly LHT 52cm Nice Bicycle I think.

If its just chrome paint then you can use oven cleaner of paint remover but if its real chrome I can't help on that.
Anyway good luck on it.
KDC1956 is offline  
Reply
Old 12-08-09 | 06:50 PM
  #3  
DannoXYZ's Avatar
Senior Member
Titanium Club Membership
20 Anniversary
 
Joined: Jul 2005
Posts: 11,754
Likes: 26
From: Mesa, AZ

Bikes: Moots RCS, tandem, beach-cruiser, MTB, Specialized-Allez road-bike, custom track-bike

Oven cleaner won't remove paint very well. Use an aircraft paint-stripper. Wear thick rubber gloves.

Real chrome (which looks likely) is extremely difficult to remove because chrome-plating starts with a copper electroplate, then tin, then finally chrome on top. No way to dissolve all three of those metals easily. Mechanical stripping by sanding is the only way to get it back to bare steel. But that's not easy or even necessary. Just sand the chrome to a 400 finish, primer then paint like regular bare steel
DannoXYZ is offline  
Reply
Old 12-08-09 | 07:32 PM
  #4  
mrrabbit's Avatar
Senior Member
Titanium Club Membership
15 Anniversary
 
Joined: Dec 2007
Posts: 3,518
Likes: 40
From: San Jose, California

Bikes: 2001 Tommasini Sintesi w/ Campagnolo Daytona 10 Speed

Originally Posted by DannoXYZ
Oven cleaner won't remove paint very well. Use an aircraft paint-stripper. Wear thick rubber gloves.

Real chrome (which looks likely) is extremely difficult to remove because chrome-plating starts with a copper electroplate, then tin, then finally chrome on top. No way to dissolve all three of those metals easily. Mechanical stripping by sanding is the only way to get it back to bare steel. But that's not easy or even necessary. Just sand the chrome to a 400 finish, primer then paint like regular bare steel

As DannoXYZ suggested...check to see if it's really paint or actually chrome plating. If it's chrome plating...leave it there...follow his suggestions above.

=8-)
mrrabbit is offline  
Reply
Old 12-08-09 | 07:34 PM
  #5  
joejack951's Avatar
Senior Member
20 Anniversary
 
Joined: May 2004
Posts: 12,103
Likes: 96
From: Wilmington, DE

Bikes: 2016 Hong Fu FM-079-F, 1984 Trek 660, 2005 Iron Horse Warrior Expert, 2009 Pedal Force CX1, 2016 Islabikes Beinn 20 (son's)

With chrome, the outer layer (the chrome look you see) can be bead blasted away quite easily. It's extremely thin and brittle. The copper underneath, however, isn't so easy. I'm not sure if it has to do with the thickness of the layer or the softness of the copper, but you'll likely give up trying to blast it away just I did before you even begin to see the underlying metal. Take Danno's advice.
joejack951 is offline  
Reply
Old 12-08-09 | 08:04 PM
  #6  
Senior Member
 
Joined: Aug 2005
Posts: 33,657
Likes: 1,119
From: Pittsburgh, PA

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Originally Posted by joejack951
With chrome, the outer layer (the chrome look you see) can be bead blasted away quite easily. It's extremely thin and brittle. The copper underneath, however, isn't so easy. I'm not sure if it has to do with the thickness of the layer or the softness of the copper, but you'll likely give up trying to blast it away just I did before you even begin to see the underlying metal. Take Danno's advice.
the only way to effectively remove chrome (and the Cu and Ni underlayers) is to electrolytically strip it, i.e.reverse electroplate it. This is not cheap or easy and you must have access to a plating shop that knows what it is doing.

Otherwise just wet sand the surface to achieve a bit of "tooth", prime and paint as Danno recommended.

BTW, are you sure it's really chrome plate or, possibly just regular paint made to look like chrome. If the latter, paint stripper will remove it just like any other paint.
HillRider is offline  
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
tommasinisun
General Cycling Discussion
8
05-09-16 02:14 PM
yannis
Bicycle Mechanics
12
04-11-12 07:49 AM
illdthedj
Bicycle Mechanics
8
11-01-11 04:21 PM
youngandcurious
Singlespeed & Fixed Gear
11
05-19-10 08:58 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.