Time to tension the Brooks saddle?
#1
Bourbon junkie
Thread Starter
Join Date: Aug 2007
Location: NorCal
Posts: 722
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Liked 0 Times
in
0 Posts
Time to tension the Brooks saddle?
Seems like my team pro's developed a bit of sag. Wanted opinions since the team pro has a reputation for being the hardest of the brooks line, I can't remember what it looked like out of the box, and this one only has about 1600 miles on it. Put a white board across the top of the saddle and took a photo. What do you guys think?
Last edited by ricebowl; 09-05-11 at 04:07 PM.
#2
Senior Member
Join Date: Jun 2010
Location: South
Posts: 415
Bikes: Had a Surly Cross Check - was totaled in recent accident. Sadly now just a Fuji Crosstown as a backup bike.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Disclaimer: I have no idea what I'm doing half the time.
With that being said, I tightened my flyer when the leather had my rear contacting the support rails underneath. I tightened enough so that when I sat on it, that did not happen. I had to tighten more than the 1/4 of a turn you hear about. Worked for me.
With that being said, I tightened my flyer when the leather had my rear contacting the support rails underneath. I tightened enough so that when I sat on it, that did not happen. I had to tighten more than the 1/4 of a turn you hear about. Worked for me.
#3
Senior Member
Join Date: Sep 2008
Location: Sesame Street
Posts: 266
Bikes: Swobo Folsom, Diamond Back Master TG, Mongoose Alta, Huffy Daisy Tandem
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
That does not appear to be an unduly amount of sag, however, if you are experiencing creaking or excessive sway, I would tighten it up just a tad - the famed quarter turn should be plenty. My B17 has a similar amount of unweighted sag and it is just as comfortable as can be. Good luck!
Cheers
lverhagen
Cheers
lverhagen
#4
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,786
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3588 Post(s)
Liked 3,400 Times
in
1,934 Posts
Are the skirts splayed out? Is it uncomfortable? Did it get soaked by rain?
If not, if it were my saddle, I'd just leave it alone. I have an almost 30 year old Team Pro with uncounted miles on it and have never had to touch the tension bolt.
If not, if it were my saddle, I'd just leave it alone. I have an almost 30 year old Team Pro with uncounted miles on it and have never had to touch the tension bolt.
#5
Happy go lucky
Join Date: Aug 2011
Location: Illinois
Posts: 286
Bikes: 2010 Nagasawa (Track), EAI Bareknuckle (Track), Custom Jonny Cycles (Track), 90's Eddy Merckx (Road), 2002 Colnago Tecnos, 200? Felt F60 (Road), 1992 Schwinn Paramount Series 3 (Road)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
They're not generally flat, I know some older ones sometimes are. But the amount of sag you have seems normal to me. I have a swift, and I only tightened it once after about 10,000 miles when I randomly happened to notice it was feeling bouncy.
#6
Senior Member
Join Date: Mar 2010
Posts: 919
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
1/4" drop at the lowest point is normal. I used to ride a B17 with 4mm thick leather. This saddle sagged badly (1/3"-1/2") after only 800 miles.
Switched to an Imperial Narrow with 5mm thick leather. The skirts were laced tight. +3600 miles with only 1/4" gap at the lowest point. Lacing the skirts should drastically reduce sagging.
What is the nominal thickness of that Brooks Pro?
Switched to an Imperial Narrow with 5mm thick leather. The skirts were laced tight. +3600 miles with only 1/4" gap at the lowest point. Lacing the skirts should drastically reduce sagging.
What is the nominal thickness of that Brooks Pro?
#8
Map maker
Join Date: Feb 2008
Location: Richmond,VA
Posts: 728
Bikes: Ventana El Ciclon, Walt Works 29er, Specialized Enduro (fixed up for my son).
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Liked 0 Times
in
0 Posts
you can lace it too. Sheldon tells you how:
Tension Adjustment
Most leather saddles have a tension-adjusting nut located under the nose of the saddle. Fortunately, this nut usually requires a special wrench, so most people leave it alone. In almost every case that I know of where someone has tried to adjust the tension with this nut, the saddle has been ruined. My advice is to leave it alone.
If a leather saddle gradually becomes too soft and too wide after many thousands of miles, it is sometimes useful to punch a few holes in the bottoms of the side flaps and lace them together under the saddle frame.
This allows the width and firmness of the saddle to be adjusted to the rider's taste. Some older models came with a row of holes along the lower edge of the side flaps, for this very purpose.
I realize that this sounds like a lot of trouble, but most cyclists who take the trouble find it well worth while--in the end.
Most leather saddles have a tension-adjusting nut located under the nose of the saddle. Fortunately, this nut usually requires a special wrench, so most people leave it alone. In almost every case that I know of where someone has tried to adjust the tension with this nut, the saddle has been ruined. My advice is to leave it alone.
If a leather saddle gradually becomes too soft and too wide after many thousands of miles, it is sometimes useful to punch a few holes in the bottoms of the side flaps and lace them together under the saddle frame.
This allows the width and firmness of the saddle to be adjusted to the rider's taste. Some older models came with a row of holes along the lower edge of the side flaps, for this very purpose.
I realize that this sounds like a lot of trouble, but most cyclists who take the trouble find it well worth while--in the end.
#9
Bourbon junkie
Thread Starter
Join Date: Aug 2007
Location: NorCal
Posts: 722
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Liked 0 Times
in
0 Posts
Past few rides it's felt a little uncomfortable. In the past I have been surprised by a couple of unexpected rain showers but for the most part my butt was protecting the saddle. But that was months ago not recently.
#10
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,904
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,933 Times
in
1,213 Posts
Call me lazy, but...
I'll usually let things go on my B-17s until I start wondering, "Is there a more comfortable saddle I should replace this old thing with?" Then I'll go dig out the spanner, and tighten until I feel resistance. It's usually closer to 1/2 a turn than 1/4 turn for me.
I'll usually let things go on my B-17s until I start wondering, "Is there a more comfortable saddle I should replace this old thing with?" Then I'll go dig out the spanner, and tighten until I feel resistance. It's usually closer to 1/2 a turn than 1/4 turn for me.
Thread
Thread Starter
Forum
Replies
Last Post
TallRider
Classic & Vintage
37
03-04-14 06:10 PM