how to remove barends.
#1
Senior Member
Thread Starter
Join Date: Dec 2006
Posts: 224
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
how to remove barends.
how do u take out 1 bolt barends? also are they necescery? i am going to chop my bars back 1 inch.
#3
Senior Member
Thread Starter
Join Date: Dec 2006
Posts: 224
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
yes they r so once i take out the bolt i take pliers and force them out? so r they just basically hammered in there and the bolt secures them?
#4
ride the sky.
Join Date: May 2006
Location: Milford,Connecticut
Posts: 296
Bikes: mine
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If the barened is two pieces like two triangles that go together...
...then don't pull it out if the screw isn't in because the second part won't come out and you'll have that bar end in your bars forever.
Screw the bolt in all the way and take a screwdriver and a hammer and bash it out.
...then don't pull it out if the screw isn't in because the second part won't come out and you'll have that bar end in your bars forever.
Screw the bolt in all the way and take a screwdriver and a hammer and bash it out.
#6
ride the sky.
Join Date: May 2006
Location: Milford,Connecticut
Posts: 296
Bikes: mine
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Screw the bolt in and hammer them out....or try pulling and twisting with your hand first..usually works for me.
#8
Live To Ride Ride To Live
Join Date: Jun 2005
Location: Winnipeg, Manitoba
Posts: 2,639
Bikes: Fit flow
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Unsrew the bolt a 1/4 inch, and tap it back in with a hammer, that will loosen up the wedge piece on the inside, and then it should slide right out.
__________________
BMX For Life
#10
Dig.
Join Date: Mar 2005
Location: VA
Posts: 6,168
Bikes: FTW, Gunnar Roadie, Open U.P, Gunnar Rock Hound, S&M CCR
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by BMX1992
they are haro barends so what should i do?
Anyways i had those barends and they were a pain in the ass to get in and out. Plus they are bulky and gay in general.
Don't cut your bars.
#13
ride the sky.
Join Date: May 2006
Location: Milford,Connecticut
Posts: 296
Bikes: mine
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gnr rocker
Barspin tricks are gay.
and you don't need shorter bars to do x-ups you just need to lean back a lot farther. unless your bars are over 28"
#14
Long haired freak.
Join Date: Jun 2005
Location: Still stuck in hell.
Posts: 6,281
Bikes: 2011 SE Old Man Flyer.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Longer bars make x-ups easier.
__________________
"the bus came by and I got on, that's when it all began...there was Cowboy Neal at the wheel of a bus to never-ever land."
"the bus came by and I got on, that's when it all began...there was Cowboy Neal at the wheel of a bus to never-ever land."
#15
Live To Ride Ride To Live
Join Date: Jun 2005
Location: Winnipeg, Manitoba
Posts: 2,639
Bikes: Fit flow
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gnr rocker
Barspin tricks are gay.
__________________
BMX For Life