Pump with or without inline gauge?
05-14-06 | 07:39 PM
#2
Urban Biker
Joined: Aug 2005
Posts: 731
Likes: 0
From: Durham, NC
Bikes: Trek 720 hybrid; 2007 Specialized Tricross Comp
If you're talking about monitoring how much air you're putting in your tires, yes, a gauge is probably a good idea. There's always the old squeeze test too, but a gauge seems a little more accurate and more useful than detaching the pump to test with some other gauge.
05-14-06 | 08:08 PM
#4
Plays in traffic
Joined: May 2006
Posts: 6,971
Likes: 16
From: Rochester, NY
Bikes: 1996 Litespeed Classic, 2006 Trek Portland, 2013 Ribble Winter/Audax, 2016 Giant Talon 4
+1
It saves the check, pump, check, pump, check nonsense. For me, being part of the tri-focal set, having the gauge on the pump makes it much easier to see.
It saves the check, pump, check, pump, check nonsense. For me, being part of the tri-focal set, having the gauge on the pump makes it much easier to see.
05-14-06 | 08:34 PM
#5
It's a good idea to check your inline gauge against a decent handheld gauge.
Sometimes they are off by some amount.
Once you know how much to compensate for it's not a problem.
Sometimes you get lucky and they are dead on.
Sometimes they are off by some amount.
Once you know how much to compensate for it's not a problem.
Sometimes you get lucky and they are dead on.
05-14-06 | 08:46 PM
#6
Thighmaster
Joined: Dec 2005
Posts: 193
Likes: 0
Originally Posted by jwbnyc
It's a good idea to check your inline gauge against a decent handheld gauge.
Sometimes they are off by some amount.
Once you know how much to compensate for it's not a problem.
Sometimes you get lucky and they are dead on.
Sometimes they are off by some amount.
Once you know how much to compensate for it's not a problem.
Sometimes you get lucky and they are dead on.
05-15-06 | 02:49 AM
#7
-
Joined: Feb 2004
Posts: 3,865
Likes: 41
Bikes: yes!
Originally Posted by jwbnyc
It's a good idea to check your inline gauge against a decent handheld gauge.
Sometimes they are off by some amount.
Sometimes they are off by some amount.
i always use a gauge. they make small handheld presta gauges, but i prefer the built-in if its accurate.
beware those 70% off floor pumps from nashbar/perf. my neighhbor had been inflating his mtb tires to 80psi (spec'd 50). the gauge was way off. i recalibrated it against my other 3 gauges, just used a sharpie marker to correct the gauge chart.
so now my neighbor has solved his tire explosion mystery.
05-15-06 | 09:04 AM
#10
Seņior Member
Joined: Sep 2005
Posts: 13,748
Likes: 10
From: Michigan
Bikes: Windsor Fens, Giant Seek 0 (2014, Alfine 8 + discs)
Heck, you're probably good enough just feeling the tire, but if you care about the PSI, get the gauge. I have the road morph with gauge and it works well for me.
You don't need to be all that accurate to get back on the road. I just like to know when I get to 60 PSI or thereabouts. I'll kick it back up to 100 when I get home.
You don't need to be all that accurate to get back on the road. I just like to know when I get to 60 PSI or thereabouts. I'll kick it back up to 100 when I get home.
__________________
Work: the 8 hours that separates bike rides.
Work: the 8 hours that separates bike rides.
05-15-06 | 10:20 AM
#11
I was having a pinch flat problem. Stupid me - I was going by my home pump gauge. It's low by about Ten pounds. Not much, but I don't inflate to the limit. It was enough for me to be getting pinch flats here and there on the rear wheel. Funny, but both my mini pumps are very accurate: a Road Morph and a Mini DX Master Blaster both with the inline gauge. They are both dead on. The Road Morph is the one I can get a road tire fully inflated with. The Master Blaster Gets me to about 65 - enough to be able to go find a real pump.
05-15-06 | 10:32 AM
#12
Infamous Member
Joined: Sep 2005
Posts: 24,360
Likes: 7
From: Ohio
Bikes: Surly Big Dummy, Fuji World, 80ish Bianchi
When it comes to guages I subscribe to the advice of ole Ronnie Reagan - 'Trust, but verify'. Even if my good floor pump says I got 80lbs in the tire, I still use my hand to test the firmness. This is especially needed with presta valves - I can't count how many people I have watched 'think' they pumped up to 100lbs or so on just two strokes because valve wasn't actually engaged with the pump.
__________________
"Let us hope our weapons are never needed --but do not forget what the common people knew when they demanded the Bill of Rights: An armed citizenry is the first defense, the best defense, and the final defense against tyranny. If guns are outlawed, only the government will have guns. Only the police, the secret police, the military, the hired servants of our rulers. Only the government -- and a few outlaws. I intend to be among the outlaws" - Edward Abbey
"Let us hope our weapons are never needed --but do not forget what the common people knew when they demanded the Bill of Rights: An armed citizenry is the first defense, the best defense, and the final defense against tyranny. If guns are outlawed, only the government will have guns. Only the police, the secret police, the military, the hired servants of our rulers. Only the government -- and a few outlaws. I intend to be among the outlaws" - Edward Abbey
05-15-06 | 01:26 PM
#13
Senior Member
Joined: Jul 2005
Posts: 2,152
Likes: 1
From: Backwoods of Ontario
If it's your only pump, go with the gauge. If it's only a frame pump, I'd go cheaper, but then I periodically lose my frame pumps. Testing by squeezing the tire is good enough to get you home.
