newbie has a rack question
#1
Member
Thread Starter
Join Date: May 2008
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
newbie has a rack question
Greetings,
I have been reading the posts on this site for several days, and I am very impressed - great site! I am currently planning to start bike commuting to my place of employment, which is approximately 7 miles one way with decent hills but nice scenery. Anyway, I am slowly outfitting my bike - a 2006 specialized sirrus, and recently added fenders. However, when i began pursuing the option of adding a rack for panniers, I noticed that my fenders used the only spot (threaded hole) for adding accessories. Is there another option for using a rack? Thanks for any suggestions.
I have been reading the posts on this site for several days, and I am very impressed - great site! I am currently planning to start bike commuting to my place of employment, which is approximately 7 miles one way with decent hills but nice scenery. Anyway, I am slowly outfitting my bike - a 2006 specialized sirrus, and recently added fenders. However, when i began pursuing the option of adding a rack for panniers, I noticed that my fenders used the only spot (threaded hole) for adding accessories. Is there another option for using a rack? Thanks for any suggestions.
#2
Senior Member
Join Date: May 2007
Location: Boston (sort of)
Posts: 3,878
Bikes: 1 road, 1 Urban Assault Vehicle
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
You could ditch the rear fender you have and get the type that fastens to the seatpost instead.
#3
Senior Member
Join Date: Mar 2007
Location: West Dorset, UK
Posts: 908
Bikes: 1983 Dawes Galaxy, 2006 Raleigh Airlite, 1982 Sun Solo (fixed)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
use longer mounting bolts and use both on the same hole
__________________
A group for all Dawes Galaxy owners to give and recieve information about them
https://flickr.com/groups/dawes_galaxy/
i jam my thumbs up and back into the tubes. this way i can point my fingers straight out in front to split the wind and attain an even more aero profile, and the usual fixed gear - zen - connectedness feeling through the drivetrain is multiplied ten fold because my thumbs become one with the tubing.
https://flickr.com/groups/dawes_galaxy/
#4
Senior Member
Join Date: Mar 2008
Location: Seattle
Posts: 385
Bikes: Bacchetta Giro 26, Novara Strada, Novara Forza
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#6
Prefers Cicero
If you can, put the rack strut on first and the fender strut outside that. The rack carries the load so it needs to be right next to the frame.
On my bike the rack and fender struts cross each other and squeak, but oiling the crossover point helped.
On my bike the rack and fender struts cross each other and squeak, but oiling the crossover point helped.
#7
Member
Thread Starter
Join Date: May 2008
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks for the suggestions, however, when I took the old rack I had and tried placing it in position, it wouldn't work correctly - doesn't seem to be enough clearance for the fender underneath it. Are there various "heights" of racks?
#8
Senior Member
Join Date: Sep 2006
Location: Humboldt County Ca
Posts: 301
Bikes: All Recumbent, Strada and TT Tour
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Don't do what I did after I bought a new Rack and Pannier set for my bike.
I went into class and announced to the students that they should see my new $300,00 Rack and panniers.
Before I got to the panniers part they erupted into gales of laughter and told me I got a better deal than "Suzie Q", she paid thousands for hers.
Yeah, I turned red.
Steven
I went into class and announced to the students that they should see my new $300,00 Rack and panniers.
Before I got to the panniers part they erupted into gales of laughter and told me I got a better deal than "Suzie Q", she paid thousands for hers.
Yeah, I turned red.
Steven
#10
Member
Thread Starter
Join Date: May 2008
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I noticed that my rack I tried to recycle from an old bike has a smaller threaded hole above the larger one normally used for mounting to bike frame. Perhaps it is intended to mount fenders at that point. My concern is that the fender stays are at an odd location on the fender that one must come out through the opening in the rack to mount at the threaded hole, thereby making it a potential problem for using a pannier. Additionally, the fender seems too high to use under the rack. Do racks come in different height sizes for different bikes? Or, are they one size fits all?
#11
Prefers Cicero
Any pictures?
#12
Member
Thread Starter
Join Date: May 2008
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
It does not have an extendable leg. I bought the rack back in 2000 (?) I think. Its a performance Trans it - great rack, and very solid. At the time, I was attending Georgetown University, and commuted to classes via the bike routes in Arlington. Got a great deal on the trans it pro panniers ( a mistake on pricing by Performance, but they willingly gave me the panniers at the price listed). Only commuted less than a year, and never really used the panniers again. They are still in great shape, so I thought I would use them once I got started. Just have to find a rack that fits. I will post a picture of the rack once I get home.
#13
Senior Member
Join Date: Apr 2006
Location: San Jose, CA
Posts: 1,840
Bikes: Bianchi San Remo - set up as a utility bike, Peter Mooney Road bike, Peter Mooney commute bike,Dahon Folder,Schwinn Paramount Tandem
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
My fenders (SKS) have adjustable length struts, so the fender can be positioned wherever I want. There is a second mounting hole on my rack, where I could have attached the fender struts, but I used a longer bolt and mounted both the fender and rack through the same eyelet on the frame.
#15
DancesWithSUVs
Join Date: Apr 2005
Location: Griffin Cycle Bethesda,MD
Posts: 6,983
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Seatpost fenders only keep spray off your back,and the rack would do this anyway.
caseyclan: Try going to a shop and see what they have that will work. You could also modify your rear fender. You could chop the fender off at the seatstay bridge,since the rack covers that part anyway,and leave the front of the fender between the seat and chainstay bridges. Then you could just add a mudflap to the rear of the rack.
caseyclan: Try going to a shop and see what they have that will work. You could also modify your rear fender. You could chop the fender off at the seatstay bridge,since the rack covers that part anyway,and leave the front of the fender between the seat and chainstay bridges. Then you could just add a mudflap to the rear of the rack.
__________________
C'dale BBU('05 and '09)/Super Six/Hooligan8and 3,Kona Dew Deluxe,Novara Buzz/Safari,Surly Big Dummy,Marin Pt Reyes,Giant Defy 1,Schwinn DBX SuperSport,Dahon Speed Pro TT,Brompton S6L/S2E-X
C'dale BBU('05 and '09)/Super Six/Hooligan8and 3,Kona Dew Deluxe,Novara Buzz/Safari,Surly Big Dummy,Marin Pt Reyes,Giant Defy 1,Schwinn DBX SuperSport,Dahon Speed Pro TT,Brompton S6L/S2E-X
#16
Senior Member
Join Date: Nov 2005
Location: Knoxville, TN
Posts: 505
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yes, there are different sizes of rack. I currently use a slightly undersized one, as my LBS didn't carry the larger ones. In my case, I attached a rack extender (by Apex fenders) to keep the spray off my back.
#18
Senior Member
Join Date: Nov 2005
Location: Knoxville, TN
Posts: 505
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
A rack extender is simply a piece of plastic that's bolted to the rear of the rack, in order to extend the coverage provided by the rack from the road spray. Incredibly simple, yet surprisingly hard to find (google it for images). I got my latest extender online.
#19
Senior Member
Join Date: Feb 2001
Location: England
Posts: 12,948
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Likes: 0
Liked 7 Times
in
7 Posts
The Specialized Sirrus is totally compatable with full-sized bolt-on fender and luggage rack. Dont use any of the hack solutions above such as clamp-on MTB fender of top-plate extenders. You resort to these if your bike is not designed for commuting.
It sounds like the vertical stays of your rack are too short. You should get another rack with longer legs. My rack sits about 5mm above my fenders which is enough clearance.
If you get another rack, you dont need a top plate (you have a fender) ; the skeleton style are more versatile for attatching bunjie chords. Look for a rear light bracket for a bolt-on lamp or reflector.
Some racks have adjustable height legs. This may be useful if you switch the rack between diffferent bikes but generally you want a rack to be as simple as possible, the fewer bolts the better.
When you have only one eyelet at the bottom, the rack stays should next to the frame with the fender stays next, then a washer. Use a 5mm stainless steel allen bolt of suitable length with a greased thread. The bolt should emerge on the inside of the eyelet with a few theads visible.
Single eyelets fittings are fine even for heavy loads. The only issue may be some bending of the fender stays required to fit around the rack.
It sounds like the vertical stays of your rack are too short. You should get another rack with longer legs. My rack sits about 5mm above my fenders which is enough clearance.
If you get another rack, you dont need a top plate (you have a fender) ; the skeleton style are more versatile for attatching bunjie chords. Look for a rear light bracket for a bolt-on lamp or reflector.
Some racks have adjustable height legs. This may be useful if you switch the rack between diffferent bikes but generally you want a rack to be as simple as possible, the fewer bolts the better.
When you have only one eyelet at the bottom, the rack stays should next to the frame with the fender stays next, then a washer. Use a 5mm stainless steel allen bolt of suitable length with a greased thread. The bolt should emerge on the inside of the eyelet with a few theads visible.
Single eyelets fittings are fine even for heavy loads. The only issue may be some bending of the fender stays required to fit around the rack.
#20
Tour de Nebraska
Join Date: Sep 2007
Posts: 64
Bikes: 2007 Specialized Roubaix,2008 Moto Messenger fixed/ss,2005 Specialized Crossroads
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
[quote=sauerwald;6685188]My fenders (SKS) have adjustable length struts, so the fender can be positioned wherever I want. There is a second mounting hole on my rack, where I could have attached the fender struts, but I used a longer bolt and mounted both the fender and rack through the same eyelet on the frame.
sorry wrong post
sorry wrong post
#21
Tour de Nebraska
Join Date: Sep 2007
Posts: 64
Bikes: 2007 Specialized Roubaix,2008 Moto Messenger fixed/ss,2005 Specialized Crossroads
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#22
Member
Thread Starter
Join Date: May 2008
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
MICHEALW,
Thanks for the clear and concise reply! I suspect my current rack is of the smaller variety - the top of the fender pushes against it when I try placing the rack in position. Yes, I could adjust the fender stays to drop the fender down more, but it is a perfect distance from the tire now, and if I bring it down any more, I think it may increase the risk of rubbing against the tire. As much as I would like to recycle my rack, I may be better served getting a larger one. Too bad there isn't an aftermarket device that serves as an extension for racks that need to be heightened "just a bit". Thanks again for your suggestion, and to all other members who provided suggestions as well. This is a great site!
Thanks for the clear and concise reply! I suspect my current rack is of the smaller variety - the top of the fender pushes against it when I try placing the rack in position. Yes, I could adjust the fender stays to drop the fender down more, but it is a perfect distance from the tire now, and if I bring it down any more, I think it may increase the risk of rubbing against the tire. As much as I would like to recycle my rack, I may be better served getting a larger one. Too bad there isn't an aftermarket device that serves as an extension for racks that need to be heightened "just a bit". Thanks again for your suggestion, and to all other members who provided suggestions as well. This is a great site!