controller question
#1
Senior Member
Thread Starter
Join Date: Jul 2009
Posts: 61
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
controller question
hi everyone can anyone answer this for me ? if a motor were 48v 1000watt and it was teamed with a 48v 500watt controller then removed and teamed with a 48v 1200 watt controller would the 1200 give more torque ? or just blow up motor? what does the watts stand for i know volts = speed and amp = distance thanks in advance.
#2
Senior Member
Join Date: Jan 2009
Posts: 499
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
the only real way to destroy a motor is to make it overheat. Right? I would think that a 48v 1200 watt controller would be just fine to use on most every hub motor. And yes, a 1200 watt controller would probably have more torque in most cases unless we are talking about comparing a geared hub motor to a non-geared and then it might be close to equal. Since you are just swapping out the controllers, then yeah, the 1200 watt will give you more torque on the same hub motor.
I think watts = voltage x amps . So that 1200 watt controller will be pulling more amps out of the battery. I hope you have a battery that can handle it. Make sure you do. So 48v x 25 amps = 1200 watts. So the controller is probably a 25 amp controller where as your previous one was only 48v x 10 amps = 500 watts. Only about 10 amps. So make sure your battery can handle a 25 amp peak draw.
One more thing you need to make sure is the type of controller is okay for the motor. They have something called 120 degree types and that's probably what yours is since most motors and controllers are the same. It has to do with the hall sensors. If you are just upgrading the controller with the same brand name then it's probably fine. You need match a brushless hub motor with a brushless controller with the same kind of hall sensor circuitry. It's probably okay but it's good to make sure that it will work beforehand.
I think watts = voltage x amps . So that 1200 watt controller will be pulling more amps out of the battery. I hope you have a battery that can handle it. Make sure you do. So 48v x 25 amps = 1200 watts. So the controller is probably a 25 amp controller where as your previous one was only 48v x 10 amps = 500 watts. Only about 10 amps. So make sure your battery can handle a 25 amp peak draw.
One more thing you need to make sure is the type of controller is okay for the motor. They have something called 120 degree types and that's probably what yours is since most motors and controllers are the same. It has to do with the hall sensors. If you are just upgrading the controller with the same brand name then it's probably fine. You need match a brushless hub motor with a brushless controller with the same kind of hall sensor circuitry. It's probably okay but it's good to make sure that it will work beforehand.
Last edited by morph999; 06-25-10 at 12:17 PM.
#3
Senior Member
Join Date: Jun 2008
Posts: 415
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
To start with the rating on motors doesn't mean as much as you might think. For example a 500w motor running with a 35a controller will actually produce more then twice it's rating. Most controllers are rated in amperage but some distributors like to use watts. For sure you will have more torque and speed using a 1200w controller over a 500w controller. Will it damage the motor? Not likely but I would check on the temp. of the motor after a hard run. It should never get so hot that you don't want to hold you hand on it. If this does happen just don't use full throttle except when you need added power for climbing and or exceloration. The rest of the time use a reduced throttle and you should be fine. Using over size controllers in this manner is very common. Keep in mind that you need a battery pack that can handle the 1200w controller too.
Thread
Thread Starter
Forum
Replies
Last Post
Slipinn
Electric Bikes
5
06-22-17 01:41 PM