Go Back  Bike Forums > Bike Forums > Folding Bikes
Reload this Page >

Swift folders

Notices
Folding Bikes Discuss the unique features and issues of folding bikes. Also a great place to learn what folding bike will work best for your needs.

Swift folders

Old 06-16-13, 02:33 AM
  #3301  
Newbie
 
Join Date: Sep 2012
Posts: 63
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by Paul Braithwait
Avon Cycles in Bath (where I bought my Swift 7 years ago) built me a nice pair of wheels with Sun rims and Ultegra hubs. I use these in the summer (when the rain is warmer) and keep the original wheels, with heavier tyres, for the dark days of winter.
When the rain is warmer, that made me laugh, we haven’t been short of a bit of rain have we.

Hi Paul. What spoke count did you use and are they a noticeable improvement on the stock wheels or is it mainly the tyres? I was stuck on 16 front and 24 rear for lightness but maybe it’s not so necessary.
michael432000 is offline  
Old 06-17-13, 02:20 AM
  #3302  
Senior Member
 
Join Date: Jun 2006
Location: Lewes, UK
Posts: 116

Bikes: Brompton, Xootr Swift, Scott Spark, Giant Anthem, Yeti AS-R, Dahon Helios

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
If anyone in UK is after a capreo hub for a wheel build - I got a 24H Capreo rear hub I no longer need. Used for one year, but the cassette I think is virtually new. After buying it I took up track racing, and riding with a very high cadence became useful training and I didn't need a high top gear any more.
rickybails is offline  
Old 06-17-13, 09:20 AM
  #3303  
Senior Member
 
Paul Braithwait's Avatar
 
Join Date: Aug 2006
Location: Carlisle, in England's Lake District, just a few miles south of the border with Scotland.
Posts: 323

Bikes: A Bianchi C2C road bike, a steel framed touring bike and a Xootr Swift folder which has made the rest redundant!

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 23 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by michael432000
When the rain is warmer, that made me laugh, we haven’t been short of a bit of rain have we.

Hi Paul. What spoke count did you use and are they a noticeable improvement on the stock wheels or is it mainly the tyres? I was stuck on 16 front and 24 rear for lightness but maybe it’s not so necessary.
The rims are Sun CR18 and have 32 spokes front and back - laced from Shimano Ultegra hubs. I have them shod with Schwalbe Marathon Racer tyres, which offer a good balance between low rolling resistance and puncture protection. The original wheels have Schwalbe Marathon Plus tyres which are heavier and provide greater protection against flats. The problem with the Marathon Plus tyres on our road surfaces is that they drag a bit. It's almost like trying to rip Velcro apart! The roads around here have stone chippings embedded in the Tarmac which the Marathon Plus tyres grip with force. There's no chance of skidding but not much chance of freewheeling either! The new wheels are lighter than the stock ones (without tyres) and roll very well. They make the bike a bit lighter and (having black rims) look good. If you use slick tyres they would be even lighter.

Avon Cycles said they could build wheels using any combination of rims, spokes and hubs. I chose Ultegra because Shimano is compatible with the stock SRAM gears on the Swift.
Paul Braithwait is offline  
Old 06-18-13, 01:25 PM
  #3304  
Senior Member
 
Paul Braithwait's Avatar
 
Join Date: Aug 2006
Location: Carlisle, in England's Lake District, just a few miles south of the border with Scotland.
Posts: 323

Bikes: A Bianchi C2C road bike, a steel framed touring bike and a Xootr Swift folder which has made the rest redundant!

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 23 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Drop the bars part 3!

I managed to track down some flat handlebars that have a short length of bulge in their middle. They are Thorn AL7075 Narrow Flat MKII 'bars from SJS Cycles in Bridgewater UK. Thorn is the 'house brand' for SJS Cycles. The bars are made to accommodate Gripshift gear changers, brake levers,'bar grips and 'bar ends without making things too cramped. It is possible to slide the Gripshift almost to the 'bar stem - there is just enough space left to squeeze in a light bracket.

As you can see from the photo there is plenty of room for my right hand to fit comfortably on the bars without touching the gear selector. The whole 'bar assembly is covered with two layers of tape with gel pads (under the tape) encasing the top flat section. The extra padding not only gives a comfortable hand hold it also offers good insulation from road vibration. I think the arrangement is a nice, clean solution to fitting drop 'bars whilst retaining a twist grip.

To make up for the rather industrial photo of the new 'bars,(the cable you can see is from the gripshift) I hope you like a rare picture of the Swift (taken today) on a British summer day - a rare thing indeed!
Attached Images
File Type: jpg
SSCN4984.JPG (66.0 KB, 178 views)
File Type: jpg
SSCN4985.JPG (66.4 KB, 154 views)
Paul Braithwait is offline  
Old 06-19-13, 12:31 AM
  #3305  
Senior Member
 
Join Date: Jan 2010
Posts: 433
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
I have decided to sell my Swift. Its a great bike but thinning the herd I have decided to keep my Bromptons and my Dahon Uno.

Really enjoyed adding e assistance and tinkering.




Will probably take the motor and electrics off and put the bike back to its stock config and then list it on ebay.

Jerry
jerrysimon is offline  
Old 07-21-13, 10:20 AM
  #3306  
Senior Member
 
DVC45's Avatar
 
Join Date: Dec 2006
Posts: 3,896
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 12 Times in 7 Posts
Just scored a used one for cheap!



Haven't ridden it yet, but ideas for mods is already swirling in my mind.
DVC45 is offline  
Old 08-16-13, 06:53 AM
  #3307  
Senior Member
 
Paul Braithwait's Avatar
 
Join Date: Aug 2006
Location: Carlisle, in England's Lake District, just a few miles south of the border with Scotland.
Posts: 323

Bikes: A Bianchi C2C road bike, a steel framed touring bike and a Xootr Swift folder which has made the rest redundant!

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 23 Post(s)
Likes: 0
Liked 1 Time in 1 Post
I've just adapted a bottle cage bracket to be a Q/R rear light fitting for my Swift.

SKS make a Q/R fitting for bottle cages. They can be snapped onto most bike frames in seconds and can also be quickly removed - handy for a folder. I use one on the front of my Swift to hold a bottle cage but have used another one to hold a rear light around the seat post. The light holder is a Cateye belt type clip through which I drilled a 5mm hole (easily done as the clip is plastic(ish). A bolt with nut at the back attaches the clip to the Q/R bracket and the light just clips into it. The bracket can be angled to ensure the light is at the right elevation. Easy to remove for folding and secure when attached. Hope this helps you find a home for a rear light.
Attached Images
File Type: jpg
SSCN5019.JPG (55.4 KB, 145 views)
File Type: jpg
SSCN5020.JPG (60.5 KB, 167 views)
File Type: jpg
SSCN5021.JPG (54.4 KB, 162 views)
Paul Braithwait is offline  
Old 08-28-13, 09:26 PM
  #3308  
Newbie
 
Join Date: Aug 2013
Posts: 1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Xootr Swift

Where did you find a used Xootr? I don't see any on Craigslist.
SMCCalif is offline  
Old 09-08-13, 06:53 AM
  #3309  
Newbie
 
Join Date: Sep 2012
Posts: 63
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Awesome.



Apologise poor quality photo.
Attached Images
File Type: jpg
SP_A0146.jpg (80.3 KB, 350 views)
michael432000 is offline  
Old 09-09-13, 10:41 AM
  #3310  
Senior Member
 
Join Date: Aug 2007
Location: Pismo Beach, CA
Posts: 137
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Nice looking unit. Really like the drop bars. You must really be bent over while riding. Just looking at the difference of height between the bars and saddle. How tall are you? Any other up-grades or modifications?
pismocycleguy is offline  
Old 09-09-13, 11:48 AM
  #3311  
Senior Member
 
bhkyte's Avatar
 
Join Date: Sep 2008
Location: York UK
Posts: 3,027

Bikes: 2X dualdrive Mezzo folder,plus others

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 107 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
That's the kind of folder I like with the drops.

Thpught about using brifters with travel agents for the V brakes. That's what I would go for.
bhkyte is offline  
Old 09-09-13, 01:09 PM
  #3312  
Newbie
 
Join Date: Sep 2012
Posts: 63
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by pismocycleguy
Nice looking unit. Really like the drop bars. You must really be bent over while riding. Just looking at the difference of height between the bars and saddle. How tall are you? Any other up-grades or modifications?
Hi pismocycleguy.

I love these handlebars (3T Ergosum pro); they have a very shallow drop and look smaller than normal drops, which really suit the Swift in my opinion.





I am 1.72m, lean and wiry and I find this set-up extremely comfortable. I donít find the supposedly harsh set-up with narrow high-pressure tyres and I-Beam seatpost and saddle to be a problem at all; in fact I love it. Of course a large person riding to the shops in trainers would probably disagree.

Some nice black cranks to go with the 57T TA chainring would be nice. And a custom-made quality steel fork would be nice too but hard to justify the cost.

Kind regards

Michael.
Attached Images
File Type: jpg
SP_A0152 - Copy.jpg (92.0 KB, 243 views)
File Type: jpg
SP_A0153 - Copy.jpg (94.8 KB, 235 views)
michael432000 is offline  
Old 09-09-13, 02:53 PM
  #3313  
Senior Member
 
bhkyte's Avatar
 
Join Date: Sep 2008
Location: York UK
Posts: 3,027

Bikes: 2X dualdrive Mezzo folder,plus others

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 107 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Carbon crank and black chainring would look great imo.
Can you get much range of seatposts for a friday? Like you can get a thudbuster and a sdp beam for dahon.
bhkyte is offline  
Old 09-22-13, 10:49 PM
  #3314  
GN BIKN
 
Join Date: Sep 2005
Location: Portland OR
Posts: 255

Bikes: 1990ish MTB converted to 'cross, custom Vulture 29"er, Swift 2-speed Automatix folder, Madsen cargo bike

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Long time no post, but I thought I should mention that I've gotten my Swift back up and running. Last fall I finally came to the realization that I didn't really enjoy doing my 12-14 mile evening commute on it (morning commute is train-assisted and shorter). I prefer riding on semislicks to deal with occasional gravel, and I haven't found a suitable 406 tire that performs even close to what I get with my Ritchey Speedmaxes in 700c; and I've also found that gravel, potholes and the long steep descent near the end of my commute are just a whole lot less sketchy on the big wheels, especially in the winter.

So I switched back to my cyclocross-ish bike for my daily commute, and rebuilt the Swift's fantastic Sturmey-Archer X-RDC drum brake/cassette freehub into 700c, leaving the Swift without a rear wheel and gathering dust for a few months. But while I'm not really keen on the Swift for longer rides, I do like the idea of having it around for shorter trips up to 3-5 miles. That's still good for most of my local non-commute trips, and for getting me to and from the train if I don't feel like doing the full ride home in the evening. And I still want to keep it around as a travel bike.

So my new vision for restoring the Swift to life was to make it as simple as possible to ride (along the lines of GP's "just ride" mentality, I suppose), and simpler to fold and pack up for travel. I can't quite go singlespeed with the amount of riding I have to do in Portland's hills, so some sort of gear hub seemed the way to go. After a lot of research it seemed that the SRAM Automatix 2-speed hub gets mostly stellar reviews (in stark contrast to the Sturmey 2-speed kickback hub, BTW). I love the idea of NO cables going to the back of the bike, so I went for the coaster brake version. Well, as it turns out I agree with the reviews: it's brilliant. Shifts are as silent, instant and feel-nothing-but-the-change-in-ratio as any gear hub, and it's just a no-brainer to ride. Downside of this hub is that the shift comes in early, at about 8.5mph with a 1.95 rear tire. So in order to avoid knee strain climbing in the 9-11mph range (where I spend a LOT of my time) I've ended up gearing it lower than might seem optimal: just 39x17 currently, which yields gears of about 44 and 60 inches (on this hub, the "low" gear is direct drive and the "high" gear is overdrive). That's lower than I originally expected for a mostly-road bike, but actually is pretty good for the short trips that I'm mostly going to use it for.

I still have the Sturmey drum brake/dynamo hub in front, which is in keeping with the "just ride" simplicity I want for this bike: the headlight and taillight come on automatically when you start rolling and turn off when you stop. No fussing with light switches. I've also swapped the drop bar back out in favor of a short flat bar with stubby bar ends, for a more compact fold, and at my local bike co-op I found an old flat-bar canti lever with a 2-wire cable coming out of it. Sure enough, the circuit closes when you squeeze the lever! So I now I've hooked up a second taillight with power routed through this cable and now I have a totally automatic, functioning brake light!

I'm very much looking forward to using the Swift a lot this winter on the occasional dreary nights when I just don't feel like riding 14 miles in pouring rain just to get home from work, and I really don't feel like being a "cyclist". With the Swift as I've set it up, things are about as fuss-free as you can get. The train is generally too crowded in the evening to get on with my big-wheel bike, but a folding bike still allows me that option.

Last edited by GlowBoy; 09-24-13 at 03:53 PM. Reason: gearing clarification
GlowBoy is offline  
Old 09-22-13, 11:04 PM
  #3315  
Senior Member
 
smallwheeler's Avatar
 
Join Date: Aug 2012
Location: NYC
Posts: 2,380
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 151 Post(s)
Likes: 0
Liked 10 Times in 8 Posts
Originally Posted by GlowBoy
Long time no post, but I thought I should mention that I've gotten my Swift back up and running.
pics or it didn't happen, dude.
smallwheeler is offline  
Old 09-24-13, 03:08 PM
  #3316  
GN BIKN
 
Join Date: Sep 2005
Location: Portland OR
Posts: 255

Bikes: 1990ish MTB converted to 'cross, custom Vulture 29"er, Swift 2-speed Automatix folder, Madsen cargo bike

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
OK fine, here's a low-quality quick pic to start. Dude.


More about the lighting system: the rear lights are Pirahna LED side marker lights by Peterson Mfg. The taillight is amber and the brake light is red. They're designed for 12V (DC) vehicle systems, but since they're polarity-protected that means they work just fine on the AC put out by my dynohub. The front light is an MR16 LED "spotlight" with 4 focused LEDs in it, mounted in the famed Optronics holder popularized on this forum's massive Total Geekiness thread. It doesn't put out enough concentrated light for higher speed riding (probably 150-200 actual lumens with a fairly broad beam, so the throw is pretty lousy), but is adequate for the shorter urban trips I'll be doing on this bike. When I get around to it I have some better homebrew lights I plan to experiment with, but this works for now. Being designed for domestic 12V (AC) use it also works fine with my dynamo's output. Both the headlight and tail/brake lights start coming on (very flickery) at 3-5mph with the 20" front wheel, get fairly steady above 5mph and approach full brightness at 7-8mph. I'm sure the hub puts out over 12V at very high speeds, but so far I haven't burned anything out on a couple of 35mph descents. Overall I'm pretty happy to have cobbled together a very functional dynamo lighting system for less than $30 worth of parts (excluding the hub, of course).

Just to head off the more obvious Internitpicks visible in the photo:
- Yes, I know that contrary to what I said above, it actually does have a cable going to the rear. An electrical one, to power the rear lights, just no mechanical ones. One to-do item is to obtain a couple of 3-conductor connectors and splice them in so I can easily split the cable when I break the bike down for travel. BTW, I used cat 5 communication cable because that's the only thing I had around with more than 2 conductors and smaller than 14 gauge wire.
- Yes, I know the front fender is incomplete in the photo. The rest of the homemade fender has been installed since then.
- Yes, I know the wiring is messy at the moment. But it works, and being the lazy function-over-form person that I am I may not clean it up for a while.
- Yes, I know I'm missing an end plug on the left side of my handlebar. A mirror will be going in there soon.
- Yes, I know I have weeds on my driveway. No, I don't "need" to clean it up.
- Yes, the bike has two chainrings. The inner ring is the 39t used to drive the bike. The outer is a 42t functioning only as a bash/chain guard.

On a completely different note, I've finally settled upon a good way to keep the bike folded when I get on and off the train with it, but which doesn't involve fussing with straps that I have to carry separately. The other day I just figured out that if I lock the front and wheel together with a mini U-lock (which I carry anyway), the bike stays nicely together in the folded position for easy carrying. BTW a slightly longer U-lock would allow the front wheel to be secured to the left chainstay, which would then keep the bike folded but allow it to be rolled in that position.
Attached Images
File Type: jpg
20130923swiftR.jpg (54.7 KB, 294 views)

Last edited by GlowBoy; 09-24-13 at 03:55 PM.
GlowBoy is offline  
Old 09-27-13, 09:04 AM
  #3317  
Senior Member
 
Join Date: Jan 2010
Posts: 433
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
Its easy (relatively) to adjust the spring inside the SRAM A2 to change at a higher speed. I have done it on a few now

Details of how to do it with photos are shown at the bottom of the web page in the link below.

https://mccraw.co.uk/sram-automatix-review/

Take your time and note how the spring sits before you remove it.

I love the A2 and the idea of no cables but I found I could not cope with a coaster brake for city riding so now ride with a free wheel A2 and use standard brakes. Its great to just forget about gears.

Jerry

Last edited by jerrysimon; 09-27-13 at 09:09 AM.
jerrysimon is offline  
Old 10-07-13, 01:46 PM
  #3318  
GN BIKN
 
Join Date: Sep 2005
Location: Portland OR
Posts: 255

Bikes: 1990ish MTB converted to 'cross, custom Vulture 29"er, Swift 2-speed Automatix folder, Madsen cargo bike

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I may eventually get around to doing the spring mod you've described. I can live with the shift point where it is, but higher would be nicer. Agreed about the coaster brake - I'm not a huge fan of not being able to spin the cranks backward at a stoplight, but another thing I'm willing to put up with since this is not my primary bike and is mostly for shorter trips.
GlowBoy is offline  
Old 10-07-13, 11:31 PM
  #3319  
Junior Member
 
rishio's Avatar
 
Join Date: Feb 2010
Location: Berkeley, California
Posts: 17

Bikes: Xootr Swift

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Hey Guys,

I couldn't make a post in the "for sale" thread so I thought I'd post it here. I'm leaving the country for a year so I put my beloved Xootr Swift up for sale. If anyone lives in Northern California and is looking for one, here's mine:

https://sfbay.craigslist.org/eby/bik/4116413181.html
rishio is offline  
Old 11-07-13, 05:38 PM
  #3320  
Junior Member
 
Join Date: Sep 2013
Posts: 11
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
SWIFT FOLDER in AIRLINE LEGAL SUITCASE

Just got a SWIFT FOLDER with 8 speed internal hub. I packed it in a old fairly rigid soft American Tourister case.
Outside dimensions: 28"x22"x9 1/2".........The entire bike, inflated wheels and tires and rack too. I didnt have to remove the fork. And the thing is easily carried...it's lighter than my clothes.

I also had a Samsonite hard shell outsde dimensions 27"x19"x10" and it would not fit unless I removed the fork...and that was just too messy.

Tada!
Attached Images

Last edited by joliett; 11-09-13 at 03:47 PM.
joliett is offline  
Old 11-08-13, 05:02 PM
  #3321  
Senior Member
 
Paul Braithwait's Avatar
 
Join Date: Aug 2006
Location: Carlisle, in England's Lake District, just a few miles south of the border with Scotland.
Posts: 323

Bikes: A Bianchi C2C road bike, a steel framed touring bike and a Xootr Swift folder which has made the rest redundant!

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 23 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by joliett
Just got a SWIFT FOLDER with 8 speed internal hub. I packed it in a old fairly rigid soft American Tourister case.
Outside dimensions: 28"x22"x9 1/2".........The entire bike, inflated wheels and tires and rack too. I didnt have to remove the fork. And the thing is easily carried...it's lighter than my clothes.

I also had a Samsonite hard shell outsde dimensions 27"x19"x10" and it would not fit unless I removed the fork...and that was just too messy.



Tada!
You did not have to remove the fork but it appears you split the frame by removing the rear triangle. How easy was that?
Paul Braithwait is offline  
Old 11-09-13, 03:43 PM
  #3322  
Junior Member
 
Join Date: Sep 2013
Posts: 11
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by Paul Braithwait
You did not have to remove the fork but it appears you split the frame by removing the rear triangle. How easy was that?
You just need a 10mm socket and a 1/4" drive ratchet to hold the nut.
And a 4mm hex allen key.

It splits as easy as pie if you have those tools. A hex key set should always be carried anyway.

Also, the brakes and shifter cables DON'T have to be disconnected.

Last edited by joliett; 11-09-13 at 03:48 PM.
joliett is offline  
Old 12-17-13, 12:14 PM
  #3323  
my nice bike is at home
 
kraftwerk's Avatar
 
Join Date: Feb 2006
Location: Brooklyn, NY USA
Posts: 951

Bikes: 2011 BMC Race Machine / 2012 BMC Road Machine / Trek 2300 / '90's Merlin/ '70's Raleigh 20/ Ti-'swift' folder / Erickson w/S&S couplers

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 65 Post(s)
Liked 33 Times in 24 Posts
I have to remove my forks to get it into the suitcase, it's a total p.i.t.a.....
rear triangle is a breeze to remove, in comparison.
Anyway the whole thing only takes about 25 min.


Btw I have re-assembled it and 'broke-it-down' in many European train stations.

Have to be very careful not to leave any parts out or tools behind!


ps. Don't ever pack your wheels with fully inflated tires if flying, just because they fit in there.. it's not a good idea..

Last edited by kraftwerk; 01-02-14 at 09:49 PM.
kraftwerk is offline  
Old 12-21-13, 09:28 AM
  #3324  
NY / New Haven biker
 
Join Date: Apr 2006
Posts: 70
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by joliett
Just got a SWIFT FOLDER with 8 speed internal hub. I packed it in a old fairly rigid soft American Tourister case.
Outside dimensions: 28"x22"x9 1/2".........The entire bike, inflated wheels and tires and rack too. I didnt have to remove the fork. And the thing is easily carried...it's lighter than my clothes.

I also had a Samsonite hard shell outsde dimensions 27"x19"x10" and it would not fit unless I removed the fork...and that was just too messy.

Tada!
Man is that a clean bike!
procon is offline  
Old 12-21-13, 10:53 AM
  #3325  
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,350 Times in 857 Posts
Practicality: I'd hate to be putting that back together at the arrival baggage carousel , in the airport .

hauling it directly to a Hotel room would be better .. throw in a plastic tarp to keep the room's carpet clean .
fietsbob is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell or Share My Personal Information -

Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.