Bike Forums
0 2025/02/05 07:22:30
However, because the VAR 365 DOES NOT have flanges on the securing pins, the chainwhip will fit on the other remaining sprocket. This is not easily accomplished with the Suntour tool and the flanges on the pins.
However, because the VAR 365 DOES NOT have flanges on the securing pins, the chainwhip will fit on the other remaining sprocket. This is not easily accomplished with the Suntour tool and the flanges on the pins.
0 2025/02/09 08:07:34
A Campagnoloed '71 Schwinn Super Sport and '82 Lotus Super Pro hang out together.
A Campagnoloed '71 Schwinn Super Sport and '82 Lotus Super Pro hang out together.
0 2021/12/18 18:07:20
In retrospec, I should remake the upper black portion. If I add support arm sleeves to the sides the top can be lowered for a better asthetic. Yet, if I do this, the zipper will need to be moved to the front.
In retrospec, I should remake the upper black portion. If I add support arm sleeves to the sides the top can be lowered for a better asthetic. Yet, if I do this, the zipper will need to be moved to the front.
0 2025/01/22 07:04:18
0 2025/02/08 10:20:28
0 2025/02/08 10:19:25
There's not enough thickness when clamped into the bench vise, and any twisting torque can release it from the vise jaws.
There's not enough thickness when clamped into the bench vise, and any twisting torque can release it from the vise jaws.
0 2025/02/09 08:37:51
0 2025/02/08 10:18:30
Side view
Side view
0 2025/02/08 10:16:29
Not the asthetic most C&V enthusiasts desire. Too high and not a flat enough top.
Not the asthetic most C&V enthusiasts desire. Too high and not a flat enough top.
0 2025/01/22 07:04:16
Clamped in the vise, ready to go
Clamped in the vise, ready to go
0 2025/02/08 10:17:14
The smaller sprockets are removed until the two largest ones are left attached. The downside to this tool, as was noted on the Suntour tool, is that as the smaller sprockets are loosened, the largest one which is reversed threaded (as is the second largest) from the rear of the body is tightened.
The smaller sprockets are removed until the two largest ones are left attached. The downside to this tool, as was noted on the Suntour tool, is that as the smaller sprockets are loosened, the largest one which is reversed threaded (as is the second largest) from the rear of the body is tightened.
0 2025/02/09 08:04:39
It needs to be about 3/4 inch thick and square in order to be more secure in the jaws. A welder could take care of this challenge.
It needs to be about 3/4 inch thick and square in order to be more secure in the jaws. A welder could take care of this challenge.
0 2025/02/09 08:37:53
0 2025/01/26 11:43:04
0 2025/02/08 10:20:01
The four securing pins are hex machine screws.
The four securing pins are hex machine screws.
0 2025/02/09 07:54:43
The largest sprocket has been unthreaded from the body. However, by this point, the second largest sprocket is really tight and can prove challenging to remove, unless you pocess another specialized tool.
The largest sprocket has been unthreaded from the body. However, by this point, the second largest sprocket is really tight and can prove challenging to remove, unless you pocess another specialized tool.
0 2025/02/09 08:07:36
The left and right vice anchors, as well as the center body securing mechanism slide on the two guide rods.
The left and right vice anchors, as well as the center body securing mechanism slide on the two guide rods.
0 2025/02/09 07:54:40
My design
My design
0 2025/01/22 07:04:14
This tool will thread into the hub mounting threads.
This tool will thread into the hub mounting threads.
0 2025/02/09 08:26:17
In the case of this Regina 7-speed, the washer which is swagged to the knurled nut, won't fit inside low touth-count sprockets, which need to first be removed.
In the case of this Regina 7-speed, the washer which is swagged to the knurled nut, won't fit inside low touth-count sprockets, which need to first be removed.
0 2025/02/09 07:54:42
With the smallest sprockets removed, the washer and nut secure the body in a fixed position for sprocket removal with a chain whip. Care must be taken due to the smoth sides of the teeth pins. There is no flange to engage the teeth in a more secure manner (as there is on the Suntour tool).
With the smallest sprockets removed, the washer and nut secure the body in a fixed position for sprocket removal with a chain whip. Care must be taken due to the smoth sides of the teeth pins. There is no flange to engage the teeth in a more secure manner (as there is on the Suntour tool).
0 2025/02/09 08:01:19
0 2021/12/18 17:22:29
0 2021/12/18 17:22:25
0 2021/12/18 17:13:47
0 2021/12/18 17:05:23
0 2021/12/18 16:59:33
0 2021/12/18 16:44:00
0 2021/12/18 16:43:58
Mount Washington Cog Railroad cog system. Looks nothing like a sprocket for a bicycle cassette, freewheel, or "flywheel." ;)
Mount Washington Cog Railroad cog system. Looks nothing like a sprocket for a bicycle cassette, freewheel, or "flywheel." ;)
0 2021/11/19 07:30:12
0 2021/11/15 18:36:14
0 2021/09/09 04:32:24
0 2021/09/09 04:29:26
0 2021/09/05 15:36:04
0 2021/08/27 17:32:48
0 2021/08/27 17:29:58
0 2021/08/27 17:29:55
0 2021/08/27 17:24:22
0 2021/08/27 17:24:19
Despite the sticker in the top right corner, I don't have any 25T sprockets. :(
Despite the sticker in the top right corner, I don't have any 25T sprockets. :(
0 2021/08/27 17:07:14
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences | Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.