Bike Forums
0 2023/01/29 14:24:41
0 2023/01/29 14:24:40
0 2023/01/29 14:24:39
0 2023/01/29 14:24:38
0 2023/01/29 14:24:37
0 2023/01/25 20:53:43
0 2023/01/12 18:35:17
0 2023/01/08 19:33:51
0 2023/01/04 14:06:12
0 2023/01/04 14:06:03
0 2023/01/04 14:05:52
0 2022/12/05 11:01:09
0 2022/11/26 11:01:49
0 2022/11/19 10:14:06
0 2022/11/19 10:13:49
0 2022/11/18 10:03:39
0 2022/11/18 10:03:23
0 2022/10/05 21:22:57
0 2022/10/05 21:22:47
0 2022/10/05 21:22:34
0 2022/10/05 21:22:24
"pintail" head lugs!
"pintail" head lugs!
0 2022/09/17 22:48:30
0 2022/09/17 22:47:51
0 2022/09/17 22:47:05
there have been a few changes since this pic was taken, but tubing is SL, it has internal TT cable routing, Cinelli Spoiler BB with one side panto, same seat cluster as OP's
there have been a few changes since this pic was taken, but tubing is SL, it has internal TT cable routing, Cinelli Spoiler BB with one side panto, same seat cluster as OP's
0 2022/09/17 11:43:20
Another example on a "better" chain stay that's slightly smoother
Another example on a "better" chain stay that's slightly smoother
0 2022/09/07 11:19:29
here's one in the wild!
here's one in the wild!
0 2022/09/06 14:37:01
then work the rest of the tape down I do the top edge from center outward, then the bottom edge, to minimize getting wrinkles; smooth and "burnish" with the tool
then work the rest of the tape down I do the top edge from center outward, then the bottom edge, to minimize getting wrinkles; smooth and "burnish" with the tool
0 2022/09/06 14:19:37
backing paper peeled off and lined up on the stay, only the center of the tape is stuck down at first. I smooth that strip with any smooth plastic tool at hand, ideal tool is a "bone folder" but for this I used a paint brush handle
backing paper peeled off and lined up on the stay, only the center of the tape is stuck down at first. I smooth that strip with any smooth plastic tool at hand, ideal tool is a "bone folder" but for this I used a paint brush handle
0 2022/09/06 14:16:17
Here's the chain stay on a Univega for this demo, it's cleaned with alcohol but paint is chipped so final result will not be ideally smooth
Here's the chain stay on a Univega for this demo, it's cleaned with alcohol but paint is chipped so final result will not be ideally smooth
0 2022/09/06 14:13:59
...cause I cut the curves with scissors, easier to control
...cause I cut the curves with scissors, easier to control
0 2022/09/06 14:12:08
both cut with ruler/straight edge and Xacto knife, but rounded ends not yet cut...
both cut with ruler/straight edge and Xacto knife, but rounded ends not yet cut...
0 2022/09/06 14:10:07
second traced.
second traced.
0 2022/09/06 14:08:59
one traced with a Sharpie, the ink wipes off later with any alcohol
one traced with a Sharpie, the ink wipes off later with any alcohol
0 2022/09/06 14:07:22
taped to a cutting board, Stay Tuff aligned with one edge, you can get 2 out of one 2" wide piece, so why not?
taped to a cutting board, Stay Tuff aligned with one edge, you can get 2 out of one 2" wide piece, so why not?
0 2022/09/06 14:05:08
for this demo I used a Stay Tuff plastic item for my template, below is a roll of the 2" 4-mil HVAC tape
for this demo I used a Stay Tuff plastic item for my template, below is a roll of the 2" 4-mil HVAC tape
0 2022/09/06 14:02:46
0 2022/08/11 18:01:43
0 2022/07/31 11:16:50
0 2022/06/26 10:01:05
Sprint LD-4850 sowing ratchet mech
Sprint LD-4850 sowing ratchet mech
0 2022/06/16 09:15:31
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences | Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.