Stripping paint off carbon?
#1
Banned.
Thread Starter
Join Date: Oct 2008
Posts: 54
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Stripping paint off carbon?
Hey guys,
I have a blue Felt and I was wondering if it is at all possible of removing the blue paint and repainting with clear coat to show the cf... anyone heard of this? done it? know of it?
thanks
I have a blue Felt and I was wondering if it is at all possible of removing the blue paint and repainting with clear coat to show the cf... anyone heard of this? done it? know of it?
thanks
#2
Former Hoarder
You can't assume that the carbon underneath the paint is the beautiful black weave you see on "naked" carbon frames - cause chances are it isn't. See, that weave is pretty much a cosmetic top layer and if paint is going on the frame, there isn't much need for the builder to throw it on there. If you were to peek under the paint, what you'd likely see would resemble black plastic tubing.
There are exceptions of course - usually with frames that have some naked area exposed.
Even if there was weave under the paint, getting the paint completely off without scratching it would be darn near impossible. Carbon frames need to be hand sanded...no stripper should be used.
55/Rad
There are exceptions of course - usually with frames that have some naked area exposed.
Even if there was weave under the paint, getting the paint completely off without scratching it would be darn near impossible. Carbon frames need to be hand sanded...no stripper should be used.
55/Rad
Last edited by 55/Rad; 10-19-08 at 10:16 PM.
#3
Aluminium Crusader :-)
Yes, you never know what you're gunna see under there.
I once sanded a painted Columbus Link fork, and the carbon looked a bit uglier than I expected, although it looked ok once I smoothed it right down a sprayed the clear on it.
I've seen sanded carbon frames with ugly joins with bits of glue showing.
I once sanded a painted Columbus Link fork, and the carbon looked a bit uglier than I expected, although it looked ok once I smoothed it right down a sprayed the clear on it.
I've seen sanded carbon frames with ugly joins with bits of glue showing.
#4
Bravo Delta
Join Date: Jan 2008
Posts: 207
Bikes: Felt F4C
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Uber bad idea. The F4C and F5C are painted for a reason... no cosmetic carbon layers as others have already mentioned. There is no way to sand off the paint and primer without taking some carbon...
#5
ka maté ka maté ka ora
Join Date: Oct 2008
Location: wessex
Posts: 4,423
Bikes: breezer venturi - red novo bosberg - red, pedal force cg1 - red, neuvation f-100 - da, devinci phantom - xt, miele piste - miche/campy, bianchi reparto corse sbx, concorde squadra tsx - da, miele team issue sl - ultegra
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 25 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Also UV rays will damage the resin holding the carbon fabric together.
#6
Administrator
Join Date: Apr 2005
Location: Hudson Valley, NY
Posts: 33,035
Bikes: Merlin Cyrene '04; Bridgestone RB-1 '92
Mentioned: 326 Post(s)
Tagged: 2 Thread(s)
Quoted: 11985 Post(s)
Liked 6,709 Times
in
3,507 Posts
. . . . and we all know what happens then -- spontaneous combustion often evoking a thermo-nuclear reaction . . . Boom!
Not pretty and makes a mess.
I'll spare you's the infamous fireball today.
Not pretty and makes a mess.
I'll spare you's the infamous fireball today.
__________________
See, this is why we can't have nice things. - - smarkinson
Where else but the internet can a bunch of cyclists go and be the tough guy? - - jdon
#7
Senior Member
Join Date: Jun 2008
Location: Kent, WA
Posts: 315
Bikes: '07 Specialized Tarmac Pro
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
It's certainly possible if you're experienced in doing that type of sanding and have the right clear coat to refinish. If you sand into the resin below the paint you're probably fine, but if you go farther into the fibers at all, all bets are off. If you really wanted to do it, I'd call Calfee and have them do it. From their website it appears they offer such a service. I agree with the others though, it's likely it won't look quite as pretty as you might think.
https://www.calfeedesign.com/refinishpricing.htm
https://www.calfeedesign.com/refinishpricing.htm
#8
Senior Member
Join Date: Nov 2006
Location: Florida
Posts: 1,296
Bikes: 2007 Orbea Onix TDF,2008 Orbea Orca in Red
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts