Lace a Brooks On-The-Cheap?
#26
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 12,902
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Mentioned: 141 Post(s)
Tagged: 0 Thread(s)
Quoted: 1463 Post(s)
Liked 2,220 Times
in
973 Posts
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
#27
Standard Member
Thread Starter
Join Date: Apr 2009
Location: Brunswick, Maine
Posts: 4,280
Bikes: 1948 P. Barnard & Son, 1962 Rudge Sports, 1963 Freddie Grubb Routier, 1980 Manufrance Hirondelle, 1983 F. Moser Sprint, 1989 Raleigh Technium Pre, 2001 Raleigh M80
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1301 Post(s)
Liked 942 Times
in
490 Posts
Nor did they punch-out the hole rows after they had put the cover on the saddle frame. Pulling and twisting to gain access to the under-neath is not optimal, especially for dried leather from (Sturmey era) 1980's.
__________________
"In every job that must be done, there is an element of fun. You find the fun, and - SNAP - the job's a game!"
"In every job that must be done, there is an element of fun. You find the fun, and - SNAP - the job's a game!"
#28
Senior Member
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,897
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1867 Post(s)
Liked 666 Times
in
508 Posts
On that bridge-plate saddle, did you add a layer of leather to the top? I'm guessing so, and that would explain your line of bolts along the bottom edge between the cantle and the plate, and use of longer bolts rather than rivets to securethe top to the cantle. Given all that theorizing, how does it feel? And what modern model of Brooks would have the same cantle width as yours?
#29
Senior Member
Join Date: Sep 2011
Location: Baltimore MD
Posts: 3,336
Bikes: '72 Motobecane Grand Record, '72 Gitane tandem, '72 Raleigh Super Course, '73 Raleigh Gran Sport, '73 Colnago Super, '76 Fiorelli Coppi, '78 Raleigh SBDU Team Pro, '78 Trek 930, '81 Holdsworth Special 650B, '86 Masi GC, ’94 Bridgestone RB-T
Mentioned: 67 Post(s)
Tagged: 0 Thread(s)
Quoted: 787 Post(s)
Liked 524 Times
in
284 Posts
I have laced old Brooks saddles to prevent the skirts from flaring out. Two holes per side is plenty for that, not too close to the sides. I've also had luck soaking the whole thing in room-temperature water for a few hours, then reshaping the saddle, with straps and stuffing it with newspaper as it dries. That can work surprisingly well.
__________________
The man who dies with the most toys…is dead. - Rootboy
The man who dies with the most toys…is dead. - Rootboy
Last edited by jeirvine; 10-15-23 at 09:00 AM.
Likes For jeirvine:
#31
Senior Member
Regarding those saddles above, I really like the idea of using coins instead of washers but the workmanship is not good and the protruding Allen heads are just not okay by me (potentially hurtful/injurious to the rider). Even a shallow pan head or a true rivet would be better (smooth surface).
I work in an arena where critique is a necessary and welcome thing. We do not fool around and we don't take it personally. Critique is a learning opportunity. It is neither uncivil, unkind nor insulting. It may not be diplomatic but diplomacy is way down on the list of priorities if it gets in the way of clear, concise critique.
Different people have different contexts.
Last edited by Bad Lag; 10-15-23 at 03:39 PM.
#32
Senior Member
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,992
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26464 Post(s)
Liked 10,423 Times
in
7,238 Posts
Likes For 3alarmer:
#33
Senior Member
Join Date: Oct 2016
Location: Cambridge UK
Posts: 852
Bikes: 1903 24 spd Sunbeam, 1927 Humber, 3 1930 Raleighs, 2 1940s Sunbeams, 2 1940s Raleighs, Rudge, 1950s Robin Hood, 1958 Claud Butler, 2 1973 Colnago Supers, Eddie Merckx, 2 1980 Holdsworth, EG Bates funny TT bike, another 6 or so 1990s bikes
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 331 Post(s)
Liked 332 Times
in
185 Posts
Brooks intransigence
Brooks refuse to sell leather skins. They sell everything else as spares except the important bit.
The metal bridge is a feature on the Swallow model. In the photo I used a piece of aluminium and simple bolts ,nuts and washers. It works just fine.
Riveting the nose cone is difficult as two of the rivets are horizontal and a very solid one-of-a-kind jig is needed.
Soaking leather in water and stretching works well if you tighten a little at a time and water doesn't seem to weaken the leather.
Use the dubbing sparingly, a teaspoon every 12 months is plenty.
The metal bridge is a feature on the Swallow model. In the photo I used a piece of aluminium and simple bolts ,nuts and washers. It works just fine.
Riveting the nose cone is difficult as two of the rivets are horizontal and a very solid one-of-a-kind jig is needed.
Soaking leather in water and stretching works well if you tighten a little at a time and water doesn't seem to weaken the leather.
Use the dubbing sparingly, a teaspoon every 12 months is plenty.
Last edited by Johno59; 10-18-23 at 07:30 PM.
Likes For Johno59:
#34
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,857
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2299 Post(s)
Liked 2,059 Times
in
1,257 Posts
I have an inexpensive leather punch and would use that. It is fast and cuts clean holes and is easy to use for the side of a saddle. Placement is not as precise as I might like, so I would work out how to do that.
If I were drilling holes in leather, I would use a "brad point bit" (I have a set for woodworking). These have a central point for locating the hole but cut very clean holes because they cut starting at the perimeter (not the center).
If I were drilling holes in leather, I would use a "brad point bit" (I have a set for woodworking). These have a central point for locating the hole but cut very clean holes because they cut starting at the perimeter (not the center).
Likes For clubman:
#35
Senior Member