How long does it take you to fix a flat?
#27
Senior Member
Most of my flats are radial tire wire. Unless it is all big, I insert a new tube, inflate, and so any patches at home. Under 10, unless in the rain or adverse conditions. Even so, my repair at home is about 15 minutes using a repair stand to make it easier.
#28
Senior Member
Join Date: May 2008
Posts: 7,384
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 800 Post(s)
Liked 218 Times
in
171 Posts
How long does it take you to fix a flat?
I carry two new tubes on a long ride, and I never seem to get around to patching flats though I do carry a patch kit for the worst circumstances.
As a year-round cycle commuter, time to fix is often critical, especially in the Winter.
And… I also employ this preventative measure,to hopefully forestall flats, especially because as @FlMTNdude noted
So replacing the floppy tire liner after a repair adds a few minutes.
BTW, just a few minutes ago I posted about living through a flat-tire horror story:
Having gotten two flats on my rear tire in a week's time, I've found it takes me about 20-25 minutes at a liesurely pace to:…
It seems like most of my flats are in pouring rain or when it’s 42 degrees and raining. It’s basically a race for me. I prefer to replace the tube and patch it at home. Say 10ish minutes.
As a year-round cycle commuter, time to fix is often critical, especially in the Winter.
BTW, just a few minutes ago I posted about living through a flat-tire horror story:
I just posted this PM yesterday about our cross-country tour on Merciers with fully loaded panniers in 1977:..
Back in' 72, I think it was a pretty high quality bike, costing ~$250 at that time, but we did not get a top of the line model, i.e. not Campagnolo equipped. They did have sew-up tires and we actually used the bikes for touring pretty well in Michigan and Ontario.
We then used them to ride cross country and the sew up tires we're the worst part of the trip due to an excessive number of flats, the difficulty of repair, and the need to take a couple days off to find a city with a shop that sold them, but we made it.
Back in '77 it was a lot harder to get good information--no Internet!
Back in' 72, I think it was a pretty high quality bike, costing ~$250 at that time, but we did not get a top of the line model, i.e. not Campagnolo equipped. They did have sew-up tires and we actually used the bikes for touring pretty well in Michigan and Ontario.
We then used them to ride cross country and the sew up tires we're the worst part of the trip due to an excessive number of flats, the difficulty of repair, and the need to take a couple days off to find a city with a shop that sold them, but we made it.
…When we did our cross-country honeymoon, we brought six spare tires. It seemed we would get a flat tire about every three days, just as the sticky glue-grime wore off our hands.
Twice on the tour we had to ditch the bikes in a motel and hitchhike to a city to buy more tires (in Flagstaff, AZ and Pueblo, CO), losing two otherwise rest days, plus all the delays and time expended fixing flats.
We switched wheels soon after arriving in Boston.
Twice on the tour we had to ditch the bikes in a motel and hitchhike to a city to buy more tires (in Flagstaff, AZ and Pueblo, CO), losing two otherwise rest days, plus all the delays and time expended fixing flats.
We switched wheels soon after arriving in Boston.
Last edited by Jim from Boston; 05-31-19 at 11:25 AM. Reason: added quote about ATMs
#29
Senior Member
Join Date: Oct 2004
Location: Huntington Beach, CA
Posts: 7,085
Bikes: Cervelo Prodigy
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 478 Post(s)
Likes: 0
Liked 87 Times
in
67 Posts
How many ever have another rider come to a complete stop to offer any kind of assistance? Or is it a quick drive-by "You OK?"
In the U.S. we typically call it a "flat" and in Europe its a "puncture".
In the U.S. we typically call it a "flat" and in Europe its a "puncture".
#30
Senior Member
In the U.S. we typically call it a "flat" and in Europe its a "puncture".
#31
Senior Member
Join Date: Oct 2016
Posts: 728
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 365 Post(s)
Liked 419 Times
in
248 Posts
Having gotten two flats on my rear tire in a week's time, I've found it takes me about 20-25 minutes at a liesurely pace
I've read on here before that a seasoned cyclist can replace or patch a tube in less than 10 minutes, but outside a race, I just don't see the benefit in rushing when you might botch something and end up with an unsuccessful repair. What are your experiences?
I've read on here before that a seasoned cyclist can replace or patch a tube in less than 10 minutes, but outside a race, I just don't see the benefit in rushing when you might botch something and end up with an unsuccessful repair. What are your experiences?
As for patching - I use replacement tubes until I run out, then I patch a bunch all at one time and put them back in rotation.
#32
Senior Member
Join Date: Jun 2005
Location: Kentucky
Posts: 2,601
Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 427 Post(s)
Liked 700 Times
in
436 Posts
Never timed it, but not very long-I carry a spare tube, tire levers, and a CO2 inflator. Also a patch kit. This thread has me wondering if something like this exists--I have used round insulating foam at times around the house. Why couldn't a denser version be made that could be inserted into a bike tire, as a quick temporary fix to get you home?
Likes For freeranger:
#33
Junior Member
I only carry one tube, and a patch kit, but first flat gets the new tube, and I will repair at home unless I get a second fat which has not yet happened. Takes me about 15 minutes to change the tube. I have a CO2 inflator which works well, and I carry two 16g cartridges.
#34
Senior Member
Join Date: Sep 2008
Location: NE Tennessee
Posts: 917
Bikes: Giant TCR/Surly Karate Monkey/Foundry FireTower/Curtlo Tandem
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 169 Post(s)
Liked 84 Times
in
62 Posts
My old tubeless tires were getting a bit ragged so I picked up a set of 700x28 ones that were a bit more than 28 and rubbed the bike frame. So while I waited for some 700x25 to arrive, I put on some Maxxis Detonators on a set of older rims and rode with them. Two flats in 2 rides. Gaahh!!! Then I remembered why I ride tubeless.
It takes me about 5 minutes to change a flat. I carry 3 tubes typically. Pull one bead loose and flip it over to inspect the inner surface, pull the tube. Put in a new one, pump it up and go.
FWIW. I align the tire labels so that they don't match up with the valve stem. It drives the roadies nuts on group rides.
It takes me about 5 minutes to change a flat. I carry 3 tubes typically. Pull one bead loose and flip it over to inspect the inner surface, pull the tube. Put in a new one, pump it up and go.
FWIW. I align the tire labels so that they don't match up with the valve stem. It drives the roadies nuts on group rides.
#36
Senior Member
Join Date: Jan 2009
Location: Colorado Springs, CO
Posts: 5,974
Bikes: 2015 Charge Plug, 2007 Dahon Boardwalk, 1997 Nishiki Blazer, 1984 Nishiki International, 2006 Felt F65, 1989 Dahon Getaway V
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1364 Post(s)
Liked 1,678 Times
in
827 Posts
It was raining on yesterday's ride home, and dinner was waiting, so when I got my first flat in over a year, I just replaced the tube. Seventeen minutes.
BTW, I know I sing the praises of tire liners so what happened was my rear tire had worn a little thin. A small piece of glass worked its way through the tire and eventually found its way around the side of the tire liner. Yes, a tire with a built-in barrier layer wouldn't allow this to happen, but I am happy with my set up, and semi-annual flats are a small price to pay for supple tires that resist most flats with tire liners, than without, or stiffer more puncture resistant tires that ride dull and lifeless.
BTW, I know I sing the praises of tire liners so what happened was my rear tire had worn a little thin. A small piece of glass worked its way through the tire and eventually found its way around the side of the tire liner. Yes, a tire with a built-in barrier layer wouldn't allow this to happen, but I am happy with my set up, and semi-annual flats are a small price to pay for supple tires that resist most flats with tire liners, than without, or stiffer more puncture resistant tires that ride dull and lifeless.
#37
Senior Member
Join Date: Oct 2018
Location: VA
Posts: 1,437
Bikes: SuperSix Evo | Revolt
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 733 Post(s)
Liked 815 Times
in
414 Posts
The last flat I got was during a sprint in a fast group ride, hit a rock during the sprint, but the tire didn't go flat until we were coming to a stop (thankfully!). Since I was towards the front, I was able to get it fixed by the time the end of the group rolled up on us and they didn't really have to wait on me at all. So prob five minutes or less?
Full disclosure, it was the front tire, so that makes it a lil easier, and the tires come off and go back on these wheels very easily, I can roll it on with my hands with no issues, especially when they're warm.
Full disclosure, it was the front tire, so that makes it a lil easier, and the tires come off and go back on these wheels very easily, I can roll it on with my hands with no issues, especially when they're warm.
#39
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 3004 Post(s)
Liked 2,434 Times
in
1,187 Posts
On my bike.... 3-5 minutes. On someone else's 15-20 since i'm usually trying to teach them how to do it.
Likes For GlennR:
#40
Full Member
Counting the time it takes for my wife to come and pick me up? Could be a half hour or more
Likes For bargeon:
#41
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,552
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,585 Times
in
2,344 Posts
I consider 15 minutes a good time, for me, but not necessarily a good time ...
here's a quickie! but he's not on the side of the road with his gear in a bag, etc. still, very impressive!
then there's this guy who doesn't even get off the bike!
here's a quickie! but he's not on the side of the road with his gear in a bag, etc. still, very impressive!
then there's this guy who doesn't even get off the bike!
Last edited by rumrunn6; 05-31-19 at 07:27 AM.
#42
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,552
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,585 Times
in
2,344 Posts
#43
Senior Member
Join Date: Jan 2016
Posts: 3,452
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 877 Post(s)
Liked 2,293 Times
in
1,281 Posts
I have actually had a modern racer on a carbon bike stop and offer me a tube . I was so impressed by this that I posted a thread on it. I had everything I needed to get myself going, but , after working all day and only couple of miles from my house I decided to call my wife and have her rescue me. I repaired it on the stand. I generally see us roadies offering assistance , but this guy was going the opposite direction and turned around to ask if I wanted a tube A W E S O M E ! Joe joesvintageroadbikes.wordpress
#45
Senior Member
Join Date: Jan 2005
Location: LF, APMAT
Posts: 2,752
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 624 Post(s)
Likes: 0
Liked 397 Times
in
226 Posts
I don't do patches. Replacing a tube takes me about 15 minutes. I spend a good deal of the time finding the offending object that punctured the tube.
#46
Senior Member
Join Date: Dec 2011
Location: Layton, UT
Posts: 1,606
Bikes: 2011 Bent TW Elegance 2014 Carbon Strada Velomobile
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 626 Post(s)
Liked 701 Times
in
418 Posts
Since most of my riding is commuting, I carry spare tubes (I have different size front/rear). Swap the tubes and go in about 10-15 minutes, just because I don't want to rush and pinch the new tube. I repair the tube later (usually limit tubes to 3-4 patches depending on how close together they are).
#47
Senior Member
One point five minutes.
#48
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,904
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,933 Times
in
1,213 Posts
Usually takes me 10-15 minutes to do it right, just swapping the tube out for repair at home (when I get 5-6 that need it, so the patch kit glue doesn't dry up). The biggest problem is normally finding the d@#! bit of glass or wire that caused the flat. I almost enjoyed a logging staple flat outside Glacier NP -- that one was easy to find!
I can swap the tube faster, of course. Maybe 5 minutes. BUT within 5-10 minutes of that there's usually another flat to deal with, Quicker overall to do it right the first time.
I can swap the tube faster, of course. Maybe 5 minutes. BUT within 5-10 minutes of that there's usually another flat to deal with, Quicker overall to do it right the first time.
#49
Senior Member
Join Date: Apr 2016
Location: South Carolina Upstate
Posts: 2,109
Bikes: 2010 Fuji Absolute 3.0 1994 Trek 850
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 762 Post(s)
Liked 555 Times
in
322 Posts
guy on the video did not inflate the tube a little before putting it on, do you guys do that or put it on completely flat?
#50
Newbie
Join Date: May 2019
Posts: 28
Bikes: Raleigh Criterium steel bike, Challenge Furai 2x26 recumbent bike, Koga Myata travel bike, Brompton folding bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I guess about 30 mins for me. I always wait for about 10 mins (even though this isn't necessary) to let the glue dry before I put back the innter tube.