News flash: Tools Help
12-02-17, 10:10 AM
#51
Mostly harmless ™
Join Date: Nov 2010
Location: Novi Sad
Posts: 4,430
Bikes: Heavy, with friction shifters
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1107 Post(s)
Liked 216 Times
in
130 Posts
None of the quick links from Sram are supposed to be used for more than one application. They can be used more than once but it's not suggested by Sram. The old versions of the 7, 8, and 9 speed could be opened by hand but that went away a long time ago. Even in 7 speed, Sram has made the link tighter and more difficult to open and close on the initial use. I haven't been able to close or open a new link by hand at my local co-op for the last 5 or more years I've been volunteering there.
KMC ones are more regular and those can be open and closed by hands - 7, 8 speeds especially. Didn't see any single use warnings on those. Checked their FAQ just now and it's written that their "missing link" can be reused 2-3 times?! while an 11 speed model can not be reused. Link.
I wouldn't risk re-using a 10 (or 11) speed quick links, but many people here do it regularly - for cleaning the chain and say they've had no problems - outer plates are thinner, there's less material for locking the quick link and I doubt it's a smart thing, but it seems to work with no problems.
On the other hand, for 7 and 8 speed ones, don't think there's much risk in reusing quick links a dozen times. Did you have any bad experience with those when reused often?
12-02-17, 10:33 AM
#52
Senior Member
Join Date: May 2008
Location: Zang's Spur, CO
Posts: 9,083
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3375 Post(s)
Liked 5,513 Times
in
2,856 Posts
Checked their FAQ just now and it's written that their "missing link" can be reused 2-3 times?! while an 11 speed model can not be reused. Link.
12-02-17, 11:16 AM
#53
- Soli Deo Gloria -
Join Date: Aug 2015
Location: Northwest Georgia
Posts: 14,779
Bikes: 2018 Rodriguez Custom Fixed Gear, 2017 Niner RLT 9 RDO, 2015 Bianchi Pista, 2002 Fuji Robaix
Mentioned: 235 Post(s)
Tagged: 0 Thread(s)
Quoted: 6844 Post(s)
Liked 736 Times
in
469 Posts
Reusing an 11-speed quick link isn't a problem.
Use a new link when the chain is replaced.
Use a new link when the chain is replaced.
12-03-17, 07:49 AM
#54
Senior Member
Join Date: Nov 2008
Location: South Jersey
Posts: 1,959
Bikes: Too many Bicycles to list
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 90 Post(s)
Liked 137 Times
in
45 Posts
I'd bet half the people who use master links but refuse to buy the pliers that work well, make the job braindead simple, and can be had for less than $10 also own just one crescent wrench and use it for everything. "Hey, I've got a crescent wrench, and it works. I don't need to use the right stinking tool for the job. I know owning and using tools is part of being a man, but you know what's even more manly? Not owning tools, and using something else to half-ass every job that comes along!"
Fine. Everyone's going to do what they want, and that's fine. If they want to work on mechanical things but cheap out and not use the tools intended for the job then fine. It's not against the law. I used to be a helicopter mechanic in the Army, and I learned at the ripe old age of 18 while in school for that that one should always use the right tool for the job. Doesn't matter if it's a bike, a car, a helicopter, whatever. Everything goes much easier, and you tend to break fewer things, round off fewer nuts or bolts, and overall just save time and do a better job by just using the right tool for the job.
It's ten bucks for the tool. Just use it.
Fine. Everyone's going to do what they want, and that's fine. If they want to work on mechanical things but cheap out and not use the tools intended for the job then fine. It's not against the law. I used to be a helicopter mechanic in the Army, and I learned at the ripe old age of 18 while in school for that that one should always use the right tool for the job. Doesn't matter if it's a bike, a car, a helicopter, whatever. Everything goes much easier, and you tend to break fewer things, round off fewer nuts or bolts, and overall just save time and do a better job by just using the right tool for the job.
It's ten bucks for the tool. Just use it.
Glenn
12-03-17, 08:09 AM
#55
Banned
Join Date: Apr 2010
Location: Lincoln Ne
Posts: 9,924
Bikes: RANS Stratus TerraTrike Tour II
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 3352 Post(s)
Liked 1,056 Times
in
635 Posts
Having the right tool for the job makes life a lot easier.
Example-------------when I was working as an IT serviceman, a friend had worked on a production printer all morning. After lunch I went with him and use a special test probe he should have had and fixed the machine in less than 15 minutes.
Example-------------when I was working as an IT serviceman, a friend had worked on a production printer all morning. After lunch I went with him and use a special test probe he should have had and fixed the machine in less than 15 minutes.
12-04-17, 11:22 AM
#56
Keepin it Wheel
Join Date: Aug 2011
Location: San Diego
Posts: 10,245
Bikes: Surly CrossCheck, Krampus
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Liked 3,427 Times
in
2,534 Posts
What happens if you dent the chain, or miss and hit your bike, is that your chain is dented, or your bike is hit by a rock. My bike gets hit by rocks all the time.
Thread
Thread Starter
Forum
Replies
Last Post
Sito
Bicycle Mechanics
10
01-18-16 12:28 PM
