Totally Tubular
#801
Senior Member
Join Date: Jul 2009
Posts: 11,128
Bikes: 1986 Alan Record Carbonio, 1985 Vitus Plus Carbone 7, 1984 Peugeot PSV, 1972 Line Seeker, 1986(est.) Medici Aerodynamic (Project), 1985(est.) Peugeot PY10FC
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 150 Post(s)
Likes: 0
Liked 33 Times
in
27 Posts
At the risk of being labeled a snob, I really don't see much point in cheap tubulars. They're heavy, wobbly, lumpy, harsh-riding, and flat-prone. I much prefer a decent clincher to a cheap tubular.
Decades ago it was possible to buy mid-range tubulars for training. These were decent, but not great. The Conti Sprinter was a fairly typical example, selling for $25-$30 in the mid-to-late 1980s. Now, as far as I can tell the choice is either bottom-of-the-barrel or top end. That's a real shame - but again, handmade tubulars offer a startlingly nice ride, and can be expected to go for 2000 miles on the back wheel, at which point the tires can be rotated and another 1000 or 1500 miles gotten out of them. (Yes, I know those figures will be met with disbelief by the Vittoria Rally crowd - which is illustrative, if you think about it.)
Decades ago it was possible to buy mid-range tubulars for training. These were decent, but not great. The Conti Sprinter was a fairly typical example, selling for $25-$30 in the mid-to-late 1980s. Now, as far as I can tell the choice is either bottom-of-the-barrel or top end. That's a real shame - but again, handmade tubulars offer a startlingly nice ride, and can be expected to go for 2000 miles on the back wheel, at which point the tires can be rotated and another 1000 or 1500 miles gotten out of them. (Yes, I know those figures will be met with disbelief by the Vittoria Rally crowd - which is illustrative, if you think about it.)
#802
Senior Member
Join Date: Jul 2006
Location: STP
Posts: 14,491
Mentioned: 74 Post(s)
Tagged: 0 Thread(s)
Quoted: 821 Post(s)
Liked 259 Times
in
144 Posts
At the risk of being labeled a snob, I really don't see much point in cheap tubulars. They're heavy, wobbly, lumpy, harsh-riding, and flat-prone. I much prefer a decent clincher to a cheap tubular.
Decades ago it was possible to buy mid-range tubulars for training. These were decent, but not great. The Conti Sprinter was a fairly typical example, selling for $25-$30 in the mid-to-late 1980s. Now, as far as I can tell the choice is either bottom-of-the-barrel or top end. That's a real shame - but again, handmade tubulars offer a startlingly nice ride, and can be expected to go for 2000 miles on the back wheel, at which point the tires can be rotated and another 1000 or 1500 miles gotten out of them. (Yes, I know those figures will be met with disbelief by the Vittoria Rally crowd - which is illustrative, if you think about it.)
Decades ago it was possible to buy mid-range tubulars for training. These were decent, but not great. The Conti Sprinter was a fairly typical example, selling for $25-$30 in the mid-to-late 1980s. Now, as far as I can tell the choice is either bottom-of-the-barrel or top end. That's a real shame - but again, handmade tubulars offer a startlingly nice ride, and can be expected to go for 2000 miles on the back wheel, at which point the tires can be rotated and another 1000 or 1500 miles gotten out of them. (Yes, I know those figures will be met with disbelief by the Vittoria Rally crowd - which is illustrative, if you think about it.)
I call it discerning.
But in the end, if someone wants to pay $20 for a tire and they are happy with the performance, I'm ok with that.
Just don't expect me to buy in on that opinion.
....and I would hope others could try a decent tire and go for a nice 35 to 45 mile ride.
They would feel the difference in quality I would hope.
If they don't, then the $20 tire probably is a nice fit for them.
#803
Senior Member
Join Date: Mar 2007
Posts: 6,401
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 13 Times
in
13 Posts
I dunno, but I think my wheelset with the cheap tubulars (Vittoria Rallies), still ride much plusher than my wheelset with pretty good foldable clinchers on them. If you go through a store's stock on their bins or shelves and try to find the best ones, you can have cheap tubulars with no lumps and straight base tapes......
At any rate, I'm not talented enough to identify a lumpy tire without mounting and inflating it. Even if my local dealer allowed to me open up all the boxes, I doubt I could tell which ones are lumpy and which ones aren't just by looking. And even then, I usually end up puncturing Rallys within 300-500 miles anyway.
Short version: I miss the "good old days" when decent training tubulars were available - but then, I'm glad I now have the money to not really worry about a thousand dollars a year to keep a few bicycles riding on the best tubulars ever made...
#804
Senior Member
Join Date: Mar 2007
Posts: 6,401
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 13 Times
in
13 Posts
That's not being a snob.
I call it discerning.
But in the end, if someone wants to pay $20 for a tire and they are happy with the performance, I'm ok with that.
Just don't expect me to buy in on that opinion.
....and I would hope others could try a decent tire and go for a nice 35 to 45 mile ride.
They would feel the difference in quality I would hope.
If they don't, then the $20 tire probably is a nice fit for them.
I call it discerning.
But in the end, if someone wants to pay $20 for a tire and they are happy with the performance, I'm ok with that.
Just don't expect me to buy in on that opinion.
....and I would hope others could try a decent tire and go for a nice 35 to 45 mile ride.
They would feel the difference in quality I would hope.
If they don't, then the $20 tire probably is a nice fit for them.
#805
Senior Member
Join Date: Nov 2005
Posts: 1,704
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
That's not being a snob.
I call it discerning.
But in the end, if someone wants to pay $20 for a tire and they are happy with the performance, I'm ok with that.
Just don't expect me to buy in on that opinion.
....and I would hope others could try a decent tire and go for a nice 35 to 45 mile ride.
They would feel the difference in quality I would hope.
If they don't, then the $20 tire probably is a nice fit for them.
I call it discerning.
But in the end, if someone wants to pay $20 for a tire and they are happy with the performance, I'm ok with that.
Just don't expect me to buy in on that opinion.
....and I would hope others could try a decent tire and go for a nice 35 to 45 mile ride.
They would feel the difference in quality I would hope.
If they don't, then the $20 tire probably is a nice fit for them.
https://www.ribblecycles.co.uk/sp/roa...ar/vitttuba782
#806
Senior Member
Almost all my experience with tubulars is on stuff like the Rallies. And so I agree with Chombi here. Certainly there are tubulars that are better even way-huge better. But the cheapies I have been riding on are just better than any clinchers I've used for a plusher ride. And a dude who has borrowed a couple of my bikes volunteered the same opinion. I am not the most expert opinion here by a galactic mile, but there is my limited take on it. If the boy's school fees were to be excused for the next six months, I might change my style. And BTW the flats I've had over say three years clinchers = 3; tubs = 1. Which proves nothing ...except maybe that clunky Kevlar layer in the Rally means something at least to me, which again proves nothing.
__________________
Vitus 979, Simplon 4 Star, Gazelle Champion Mondial, Woodrup Giro, Dawes Atlantis
Vitus 979, Simplon 4 Star, Gazelle Champion Mondial, Woodrup Giro, Dawes Atlantis
Last edited by Lenton58; 10-26-13 at 02:18 PM.
#807
South Carolina Ed
Join Date: Mar 2007
Location: Greer, SC
Posts: 3,894
Bikes: Holdsworth custom, Macario Pro, Ciocc San Cristobal, Viner Nemo, Cyfac Le Mythique, Giant TCR, Tommasso Mondial, Cyfac Etoile
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 346 Post(s)
Liked 294 Times
in
141 Posts
They're just tires. Ride whatever it is you want to buy and are willing to deal with.
#808
Senior Member
Join Date: Oct 2012
Location: Catania Sicily
Posts: 89
Bikes: 1980's Olmo Super Gentleman, 1992 Trek 930, 2009 Bianchi C2C
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Is there any specific tape that you would recommend? I looked at the Tufo tape however it states that it is only for Tufo tubulars?
Secondly does Stan's sealant actually work? Before I attempt to sweet talk my wife into $250 for two bicycle tires I would like some peace of mind that they would last long enough for me to enjoy them. Sicilian roads are rather rough with some broken glass here and there.
Secondly does Stan's sealant actually work? Before I attempt to sweet talk my wife into $250 for two bicycle tires I would like some peace of mind that they would last long enough for me to enjoy them. Sicilian roads are rather rough with some broken glass here and there.
#809
Senior Member
Join Date: Aug 2007
Location: Evanston, IL
Posts: 5,170
Bikes: many
Mentioned: 65 Post(s)
Tagged: 0 Thread(s)
Quoted: 1470 Post(s)
Liked 1,438 Times
in
790 Posts
Tubular glue still works for me, and I've gotten better at applying it. The tape seems pretty thick. Maybe that's why the Tufo's I tried didn't seem to stay put very well. (I think RobbieTunes has them now.) Tape is also, as I understand it, single use, and much more expensive per application than glue, so it does add to your total cost.
#810
Senior Member
Is there any specific tape that you would recommend? I looked at the Tufo tape however it states that it is only for Tufo tubulars?
Secondly does Stan's sealant actually work? Before I attempt to sweet talk my wife into $250 for two bicycle tires I would like some peace of mind that they would last long enough for me to enjoy them. Sicilian roads are rather rough with some broken glass here and there.
Secondly does Stan's sealant actually work? Before I attempt to sweet talk my wife into $250 for two bicycle tires I would like some peace of mind that they would last long enough for me to enjoy them. Sicilian roads are rather rough with some broken glass here and there.
You should be able to buy cheaper tires, like Vittoria Rallies for way less than $250/pair.
Last edited by Kactus; 01-24-14 at 12:41 PM.
#811
Senior Member
Join Date: Oct 2012
Location: Catania Sicily
Posts: 89
Bikes: 1980's Olmo Super Gentleman, 1992 Trek 930, 2009 Bianchi C2C
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
As a newbie who is learning I have read most posts that the general consensus is that higher quality tubulars like Strada Bianchi or Paris-Roubaix will last longer while providing nicer ride. If the Stans sealant can actually extend the lifespan then I may be able to justify $117 per tire.
#812
Senior Member
Join Date: Aug 2009
Location: Berkeley, CA
Posts: 7,279
Bikes: '72 Cilo Pacer, '72 Gitane Gran Tourisme, '72 Peugeot PX10, '73 Speedwell Ti, '74 Peugeot UE-8, '75 Peugeot PR-10L, '80 Colnago Super, '85 De Rosa Pro, '86 Look Equipe 753, '86 Look KG86, '89 Parkpre Team, '90 Parkpre Team MTB, '90 Merlin
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quoted: 847 Post(s)
Liked 2,219 Times
in
573 Posts
I've had experience on a range of tubulars from the 3/$50 Yellow Jersey and Ralleys, up to Challenge P-R and Dugast tubulars. The expensive tubulars are indeed much nicer. You get what you pay for, but the ride on cheaper tubulars is certainly acceptable--if you get a good one. For me, though, the rub is the consistency of the cheaper ones. I've had Ralley and YJ tires that are straight and last for well over a thousand miles. But I've also had ones that are lumpy from the start, form bulges through the casing, or prone to flats after less than a few hundred miles. The last time I purchased a 3/$50 YJ set: one was so lumpy I was instantly relegated to spare duty, another formed a bulge in the casing under the rubber after less than 200 miles (this, of course, inevitably leads to a premature puncture). IMHO, unless you are a 1%-er, you should be prepared to repair an high-end tubular if you get a flat before the tread has worn out. Some flats are bound to happen no matter what tires you run, but there's less of a return on repairing a YJ tire.
#813
Banned.
Join Date: Dec 2007
Posts: 27,199
Mentioned: 34 Post(s)
Tagged: 1 Thread(s)
Quoted: 378 Post(s)
Liked 1,414 Times
in
913 Posts
Tubular glue still works for me, and I've gotten better at applying it. The tape seems pretty thick. Maybe that's why the Tufo's I tried didn't seem to stay put very well. (I think RobbieTunes has them now.) Tape is also, as I understand it, single use, and much more expensive per application than glue, so it does add to your total cost.
I don't think Tufo tape has to be used for Tufo tires, as I'm having a heck of a time right now getting two orange Continental Sprinters off of some rims, applied with tape.
I've never used the cheap tubulars, but pick up one here and there with wheels/trades, etc, and hold them for spares. I've never used the expensive tubulars, but definitely believe that most of the $100 tubulars are likely worth the money. I use Tufo tires, both the clinching tubulars and the regular tubulars, and for the money, I've not had better. When they came from the Czech Republic, they were expensive, but there are now dealers in the US selling them for about half what they used to go for. My last purchase was 3 S33 Pro's and 3 rolls of tape for $203, delivered. I've paid as low as $103, delivered, for two of the clinching C S33 Pro's, and I'll put them up vs. about any $50 clincher/tube combo out there. I wish they were a little wider, and their cyclocross tires are very popular around here.
As you may surmise from the photo, I don't relegate tubulars to C&V bikes, and I don't discriminate when buying wheels between tubular or clincher. A good wheel is a good wheel, and I don't let the tire requirement make much of a difference.
Last edited by RobbieTunes; 09-24-20 at 10:26 AM.
#814
Senior Member
Join Date: Aug 2009
Location: Berkeley, CA
Posts: 7,279
Bikes: '72 Cilo Pacer, '72 Gitane Gran Tourisme, '72 Peugeot PX10, '73 Speedwell Ti, '74 Peugeot UE-8, '75 Peugeot PR-10L, '80 Colnago Super, '85 De Rosa Pro, '86 Look Equipe 753, '86 Look KG86, '89 Parkpre Team, '90 Parkpre Team MTB, '90 Merlin
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quoted: 847 Post(s)
Liked 2,219 Times
in
573 Posts
If you roll a tubular (which often lodges between the rim and the chain stay if it's the rear) and manage to stay upright, this is what can happen:
#816
Senior Member
Join Date: Aug 2009
Location: Berkeley, CA
Posts: 7,279
Bikes: '72 Cilo Pacer, '72 Gitane Gran Tourisme, '72 Peugeot PX10, '73 Speedwell Ti, '74 Peugeot UE-8, '75 Peugeot PR-10L, '80 Colnago Super, '85 De Rosa Pro, '86 Look Equipe 753, '86 Look KG86, '89 Parkpre Team, '90 Parkpre Team MTB, '90 Merlin
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quoted: 847 Post(s)
Liked 2,219 Times
in
573 Posts
Not recently, but yes. I've had these rims since the mid-80s. Hot summer day in the hills. Guess I was riding the brakes too hard. I rolled the rear tire and flattened out the edge of the rim sliding across the pavement with the rear locked up.
I was debating bringing these rims out of retirement if they check out as round. Though they are tad on the heavy side at ~850g for the pair (with glue residue and some tape). It was so long ago I just can't recall how bad they were when I retired them. I don't lik the idea of spending time/$ building wheels that will never stay true. I don't know, what do you think, everything else notwithstanding, would you build rims with this sort of damage? The rims are kind of cool and I like the breaking surface, esp. on ano'd rims is a plus. I bought these as a teenager in France, so they also have some nostalgic attachment. How bad could sudden wheel failure be? Don't answer that.
I was debating bringing these rims out of retirement if they check out as round. Though they are tad on the heavy side at ~850g for the pair (with glue residue and some tape). It was so long ago I just can't recall how bad they were when I retired them. I don't lik the idea of spending time/$ building wheels that will never stay true. I don't know, what do you think, everything else notwithstanding, would you build rims with this sort of damage? The rims are kind of cool and I like the breaking surface, esp. on ano'd rims is a plus. I bought these as a teenager in France, so they also have some nostalgic attachment. How bad could sudden wheel failure be? Don't answer that.
Last edited by gaucho777; 03-06-14 at 07:20 PM. Reason: I can't believe I typed breaks instead of brakes!
#817
Banned.
Join Date: Dec 2007
Posts: 27,199
Mentioned: 34 Post(s)
Tagged: 1 Thread(s)
Quoted: 378 Post(s)
Liked 1,414 Times
in
913 Posts
I'm not sure I'd build them. You may be asking the glue to do something the rim is supposed to do.
I've not rolled a tubular off. In fact, I bought a bike with tubulars, went on a 40-mile group ride, and returned home. I decided I would get new tires, and went to take the old ones off, and they weren't glued on, just pulled right off.
I did a crit once in about 95-degree weather, and the leader rolled off both tubulars at about the same time. He was using toe clips with 2 straps per foot. If it hadn't been for the hay bales, he's have lost a lot more skin.
I've not rolled a tubular off. In fact, I bought a bike with tubulars, went on a 40-mile group ride, and returned home. I decided I would get new tires, and went to take the old ones off, and they weren't glued on, just pulled right off.
I did a crit once in about 95-degree weather, and the leader rolled off both tubulars at about the same time. He was using toe clips with 2 straps per foot. If it hadn't been for the hay bales, he's have lost a lot more skin.
#818
Senior Member
Join Date: Mar 2007
Posts: 6,401
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 13 Times
in
13 Posts
I would not use those. They probably will hold up, but "probably" is not the word I'm looking for when it comes to bicycle wheels.
OTOH, I once rolled a tire and slid something like thirty feet on one edge of the rim. It actually wore the edge away to nothing - you could see inside the rim through the hole. Being a broke and idiotic junior, I glued up a new tire and rode the wheel the rest of the season without problem.
So, as a middle-aged fat guy with plenty of money and a serious aversion to any more scars, I wouldn't build up your rims. As a broke and idiotic junior, I would have built them up without a second thought and almost certainly been fine.
HTH!
OTOH, I once rolled a tire and slid something like thirty feet on one edge of the rim. It actually wore the edge away to nothing - you could see inside the rim through the hole. Being a broke and idiotic junior, I glued up a new tire and rode the wheel the rest of the season without problem.
So, as a middle-aged fat guy with plenty of money and a serious aversion to any more scars, I wouldn't build up your rims. As a broke and idiotic junior, I would have built them up without a second thought and almost certainly been fine.
HTH!
#819
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,844
Bikes: Several, mostly not name brands.
Mentioned: 154 Post(s)
Tagged: 0 Thread(s)
Quoted: 3617 Post(s)
Liked 3,454 Times
in
1,960 Posts
The Tufo tape does work with non-Tufo tires, but I recommend using the "Extreme" version of the Tufo tape in that case. It's much easier to deal with than the standard Tufo tape on a non-Tufo tire. There must be something different about the Tufo base tape that is designed to work with the Tufo mounting tapes.
#820
If I own it, I ride it
Join Date: Nov 2005
Location: Cardinal Country
Posts: 5,589
Bikes: Lejeune(14), Raleigh, Raysport, Jan De Reus, Gazelle, Masi, B. Carré(4), Springfield, Greg Lemond, Andre Bertin, Schwinn Paramount
Mentioned: 56 Post(s)
Tagged: 0 Thread(s)
Quoted: 594 Post(s)
Likes: 0
Liked 666 Times
in
314 Posts
I am surprised no one has mentioned Miyata tape. I am using it on one set of wheels so far with good results. One roll is about $50 but you get 10 wheels out of the longer roll.
I do not recommend using tape with YJ tubulars. I had basetape separating from the casing after a few rides..
I do not recommend using tape with YJ tubulars. I had basetape separating from the casing after a few rides..
#821
Banned.
Join Date: Dec 2007
Posts: 27,199
Mentioned: 34 Post(s)
Tagged: 1 Thread(s)
Quoted: 378 Post(s)
Liked 1,414 Times
in
913 Posts
The Tufo tape does work with non-Tufo tires, but I recommend using the "Extreme" version of the Tufo tape in that case. It's much easier to deal with than the standard Tufo tape on a non-Tufo tire. There must be something different about the Tufo base tape that is designed to work with the Tufo mounting tapes.
Super tip, and I'm going to try it. 10 wheels for $50 is a lot better than 4.
#824
Senior Member
Join Date: Jul 2004
Location: northern michigan
Posts: 13,319
Bikes: '77 Colnago Super, '76 Fuji The Finest, '88 Cannondale Criterium, '86 Trek 760, '87 Miyata 712
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 660 Post(s)
Liked 601 Times
in
314 Posts
I cant believe I read the entire thread. This weekend I'm being whisked into the classic world of sewups. Thanx for a good headstart, guys.
#825
Senior Member
I have removed glue in this condition using a wire brush attachment on a variable speed power drill. It came of as crystallized dust. Typical solvents were not very effective. IMHO, glue in this state of aging is dangerous.
I am assumming that this is what was there when the tubular rolled.
__________________
Vitus 979, Simplon 4 Star, Gazelle Champion Mondial, Woodrup Giro, Dawes Atlantis
Vitus 979, Simplon 4 Star, Gazelle Champion Mondial, Woodrup Giro, Dawes Atlantis