Early Trek 820 frame material
#1
Early Trek 820 frame material
I've got a early '80's Trek 820 that I've had since new. I'm thinking of doing a little restoration on it and use it for a commuter. There is a sticker on the seat tube that says the main triangle is made from Tange (sp) chromemoly steel. Does anyone know if the fork and stays are also chromemoly? Thanks
#2
80s is far too vague. There have been so many iterations of the 820 that there isn't enough here to go on. Got a picture? Even the generation of components could be helpful. Is it an "antelope"? How about "mountain track"? Lugged? Welded?
See where I'm going here?
See where I'm going here?
#3
Thrifty Bill

Joined: Jan 2008
Posts: 23,645
Likes: 1,109
From: Mans of NC & SW UT Desert
Bikes: 86 Katakura Silk, 87 Prologue X2, 88 Cimarron LE, 1975 Sekai 4000 Professional, 73 Paramount, plus more
Normally if the sticker says three main tubes are chromoly, that is code for the rest being high ten steel. If the fork has a chromoly sticker on it, then the rest is chromoly.
First 820 came out in 1987, check your serial # and specs on the vintage trek site. Specs changed just about every year, sometimes improved, sometimes for the worse.
First 820 came out in 1987, check your serial # and specs on the vintage trek site. Specs changed just about every year, sometimes improved, sometimes for the worse.
Last edited by wrk101; 07-01-12 at 05:46 PM.
#5
Ok, I went and took another look last night and the sticker says Tange 5. It does not say main tubes. When I bought the bike the front fork had a sticker on it that said chromemoly, but the fork was replaced by the dealer because it was not straight. The replacement fork looked the same, but it didn't have that sticker on it.
The bike frame is welded, not lugged. It has Exage components with the old Biopace chain rings on it. The rear brake is the U brake mounted underneath the rear stays.
Can't take a picture right now, but hope this information helps a little more.
The bike frame is welded, not lugged. It has Exage components with the old Biopace chain rings on it. The rear brake is the U brake mounted underneath the rear stays.
Can't take a picture right now, but hope this information helps a little more.
#6
It's probably an 88. No 820 specs in the 87 catalog and suntour components in 89. Have a look at the specs in the 1988 Trek catalog, I'd bet the stays are high tensile steel. That's probably the best resource you'll find to know what kind of steel your stays are, so your search will probably end here.
what color is it?
what color is it?
Last edited by IthaDan; 07-02-12 at 07:39 AM.
#7
You are exactly right sir. I was rummaging through my file cabinet and I found my original owners manual and my receipt for the bike. Purchased new in August 1988. It's solid black with turquois lettering. According to the specs (thanks for the link), that would make it chromoly frame and fork and high tensile stays. I was hoping for chromoly stays as well, but looks like that only came on the higher end bikes. Thanks very much for your help.
Thread
Thread Starter
Forum
Replies
Last Post
xiev
Classic and Vintage Bicycles: Whats it Worth? Appraisals.
24
07-23-17 07:10 PM
trekbefuddled
Classic & Vintage
12
05-10-15 09:55 AM
Drummerboy1975
Classic and Vintage Bicycles: Whats it Worth? Appraisals.
10
07-17-11 04:40 PM
tsegu
Classic and Vintage Bicycles: Whats it Worth? Appraisals.
0
08-19-10 03:18 PM








