|
Originally Posted by Zaskar24
(Post 6740430)
Sweet looking ride Mr. Smashy. What is with the silver wall on the rear tire? I can see that they are Kenda's but cannot tell which model.
|
|
Originally Posted by jim-bob
(Post 3555796)
Well hell, if it's that kind of party...
http://entirely-adequate.com/holland/holland2.jpg |
Originally Posted by willtsmith_nwi
(Post 3581977)
I used to have one of these (this one is not mine, it's another poster's):
http://img214.imageshack.us/img214/2742/bike005uh8.jpg Then it broke and I had to get a new frame and it turned into this: http://i7.photobucket.com/albums/y26...oXTDelgado.jpg Then that frame cracked and Giant would not replace the frame. So I took all the parts I could and moved it over to this: http://i7.photobucket.com/albums/y26...RightFront.jpg hahahahahaha bar ends.....:roflmao2: nice surly though, it should be single speed though |
I'm sure they'll appreciate your insightful commentary, bikerdfresh, regardless of the fact that those posts are about a year and a half old.
|
Is it possible that SIDwc-Fork is not able to use full 80mm travel?
Originally Posted by taylor p
(Post 6720212)
I have a very hard time reading your post, so I dont
But Iīll try again,and hope Iīm able to write coherent now. =O.K.? (feel free to to amend a fault) << I canīt find "SIDī06 SETTING .pdf>>:crash: = I can not find a pdf(AdobeAcrobateReaderFile) with Setting-information for a SID Wourldcup 2006year Fork. << all I can find is SERVICE and INSTALL.pdfīs! >>:crash: =I only found pdf-files with informations about serviceGuide(leg removal,Upgrading from Pure to Motioncontrol) and installing(Fork and LockOut-lever). << CAN you PLEASE -send download link?>>:crash: =Can you PLEASE send a web-link where I can download a pdf(AdobeAcrobateReaderFile)? << (Iīve read that SIDī06 donīt use the full 80mm travel?)>>:crash: =On a forum-site Iīve read that the SID Wourldcup-Fork can not use the full 80mm of Fork-travel. (Inside my Fork there is no 65mm-travel-reducer installed) still I canīt get more than 65mm of travel, even when I empty both air-chambers. Do you know anything about this issue? <<-THANKS-you helpīd me a lot->>:crash: =Thank you.You helped me a lot with prior answers. PLEASE, let me know, if you know anything about. I hope I was able to write generally intelligible this time. (usually I got not much time. Because I ride daily,I work,I study,I travel....)+~SORRY;) |
-THANK-you- a LOT. & sorry for my "shortcut-English"
2 Attachment(s)
Originally Posted by GlassWolf
(Post 6720897)
English isn't his native language, and he probably does better at English than you or I would do at his native language *laugh*
I just used the SID owners manual from SRAM's service site. It essentially suggests using half your body weight as a starting pooint for positive pressure, and about 10-20% less for negative pressure, if I recall, and tweaking it from there to your personal preference. Rebound is set using the curb test (one bounce rolling off a normal street curb) and always fill positive chamber before negative. I found flipping the boike upside down to fill or adjust the negative chamber on an SID greatly reduces the oil spraying out of the shock when you check it with a shock pump. otherwise, you get oil everywhere. Iīm about to cut steerer tube. How do I get "STARNUT" in place? Needs to go about half inch more inside. It is a special STARNUT for CARBON-tube. I know approximately how to setup positive and negative air.(got SID from 2003 since 3years)-THAN X- {by the way: I speak German,Serbian,Croatian fluently. I am learning Spanish and Italian since 3years} So SORRY for confusion!!:cry: |
|
Just another Monkey. But with new bars.
http://i281.photobucket.com/albums/k...l/P5240002.jpg |
1 Attachment(s)
Ma new ride homies!
|
|
New Ti spindle for the Profile crank and my Syncros pedals are back. Now weighs a healthy 30.5lbs with the new Topeak Mountain Morph... The I9 Enduro wheels I have on order will not be here until 3rd week of June...
http://gallery.photo.net/photo/7317911-md.jpg |
|
Nice WTP, those Commencals are so nicely finished. Cant wait till we get them in at work.
|
Do I spot a dork disc on that commencal, other than that I love how that bike looks.
|
Originally Posted by Mr. Smashy
(Post 6779626)
Do I spot a dork disc on that commencal, other than that I love how that bike works.
|
Yeah, it's a dork disc. It'll come off sometime soon.
http://img.photobucket.com/albums/v4...1/103_2438.jpg |
New here. Just started MTN biking this past fall. Open to any suggestions and recommendations for upgrades. All stock Hardrock.
http://i230.photobucket.com/albums/e...B/IMG_3588.jpg |
yo that commencal is noice.
|
More and better picts to come . . . .
http://i160.photobucket.com/albums/t...a/IMG_0891.jpg http://i160.photobucket.com/albums/t...a/IMG_0892.jpg |
Oh My!
|
Oh my god Dminor, that blindside is absolutely awesome!
I think I'm in love! That's one one bangin' colour scheme you got there. |
never mind...
|
Well D, it seems you have put a really very super cool bike together. That is really flashy,it screams look at me,I'm old ,I'm fast,I'm cool,and dogonit,people like me......sweet
|
I see you went with the floating brake, howzat going?
Nice bashy too. |
| All times are GMT -6. The time now is 09:45 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.