Renew Black/Shiny Finish on a Brooks Saddle
#1
Newbie
Thread Starter
Join Date: Aug 2005
Location: Spring Hill/Columbia, Tennessee
Posts: 63
Bikes: Cannondale R600 and Beater MTB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Liked 0 Times
in
0 Posts
Renew Black/Shiny Finish on a Brooks Saddle
My Brooks has >25,000 miles on it. The shiny/slick/original black finish is long gone. Now the brown leather shows through and I would like to make it black, shiny, and slick again. I waxed it with black Kiwi boot polish like I did for the Army boots but that 'spit shine' only holds up for 2-3 rides and the wax is gone. I tried Kiwi Heel and Edge dressing like I used to put on the combat boots, but it is not the same stuff as in the olden days. Any ideas are appreciated. Kindly - Don
#2
Senior Member
Join Date: Jun 2004
Location: Northern Nevada
Posts: 3,811
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
personally I regard my worn Brooks saddles as trophies, or at least as evidence I actually ride. If I wanted them to be black though, I'd get some leather dye (with the shoe polish in many supermarkets, or check a shoe-repair place), then maybe polish over that. It won't match the factory finish, but at least it will be black. Don't wear the white shorts on your next ride.
A shoe-repair guy might have better advice, and Tandy leather stores used to sell (may still; I haven't been in one in years) a glaze finish that might approximate the shininess for awhile. www.tandyleather.com.
A shoe-repair guy might have better advice, and Tandy leather stores used to sell (may still; I haven't been in one in years) a glaze finish that might approximate the shininess for awhile. www.tandyleather.com.
Last edited by Velo Dog; 07-10-11 at 06:09 PM.
#3
Senior Member
Join Date: Oct 2010
Location: NorCal
Posts: 188
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
+1 on the shoe repair place. A good old-school cobbler may be able to re-dye it. Hopefully you have one in your area (I'm amazed any are still around in this throwaway society we live in).
#5
Oldie but Newbie
Join Date: Jun 2011
Location: The Monadnock Region, New Hampshire
Posts: 112
Bikes: 1969 Raleigh Sprite
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
A friend who is a skilled leather worker once told me that black is the very hardest finish to produce. If I remember and understood correctly that was because the tanning oils and waxes make it difficult to get an even saturation of dye. Vat dying - something rarely done anymore in the US -- is the only away around that except for the more common coating method where the black you see is not really the leather at all but more a plastic coating on the leather.
-don
-don
#8
Newbie
Thread Starter
Join Date: Aug 2005
Location: Spring Hill/Columbia, Tennessee
Posts: 63
Bikes: Cannondale R600 and Beater MTB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Liked 0 Times
in
0 Posts
I apologize for asking. In my opinion, the bare leather allows sweat with salt and oils to penetrate and the shiny/slick finish is a lot more comfortable, but that's just me. Forgive me and drop it. Thanks for the positive input. Kindly - Don
#9
just keep riding
Join Date: Feb 2005
Location: Milledgeville, Georgia
Posts: 13,560
Bikes: 2018 Black Mountain Cycles MCD,2017 Advocate Cycles Seldom Seen Drop Bar, 2017 Niner Jet 9 Alloy, 2015 Zukas custom road, 2003 KHS Milano Tandem, 1986 Nishiki Cadence rigid MTB, 1980ish Fuji S-12S
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 33 Times
in
22 Posts
I can't offer any suggestions for restoring the original black finish, but Proofide or something similar will help protect the leather from sweat or from drying out.
#10
Senior Member
I once thought that the shiny surface was a lacquer applied at the factory to seal in the dye. But an English poster bluntly told me it wasn't. So, maybe slip an email to Brooks to find out exactly how they do achieve the shiny finish, and that could give you a clue as to how you might approach the problem. If you do find out, please let us know as my original B17 is looking a bit tatty colour-wise.
There is an interesting thread over in Touring about how to revitalise a stretched Brooks by boiling (I kid you not). It's worth a read to find out what happens. One poster is following the advice.
There is an interesting thread over in Touring about how to revitalise a stretched Brooks by boiling (I kid you not). It's worth a read to find out what happens. One poster is following the advice.