Go Back  Bike Forums > Bike Forums > Folding Bikes
Reload this Page >

Dahon Handlebar question

Notices
Folding Bikes Discuss the unique features and issues of folding bikes. Also a great place to learn what folding bike will work best for your needs.

Dahon Handlebar question

Old 04-15-19, 02:52 PM
  #1  
linberl
Senior Member
Thread Starter
 
linberl's Avatar
 
Join Date: Jun 2014
Location: SF Bay Area
Posts: 3,064

Bikes: 2017 Bike Friday PakiT. Dahon Mu Uno (trailer bike) Sold: 2003 Bike Friday NWT, 1997 Trek 720, 1993 Trek 520)

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1189 Post(s)
Liked 177 Times in 148 Posts
Dahon Handlebar question

I'd like to put more sweep on my Dahon Mu Uno so I want to replace the handlebar. However, I tried a bar I already have - and because the Dahon bar has deep ridges across the mounting area it stays put quite well - but my replacement bar is more of a normal bar without those deep ridges so it moves when I stand and press hard. The clamp is clearly designed for the bar that has those deep ridges as you can move it incrementally and clamp down. Does Dahon actually make other style bars with this "knurling" or is there some other way to make a traditional bar work?
linberl is offline  
Old 04-16-19, 07:04 AM
  #2  
pope_face
Mr. Grenade who likes pie
 
Join Date: Jun 2015
Location: Terminal City, Canada
Posts: 11

Bikes: Dahon Speed P8

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I can't say whether Dahon has different handlebars with more sweep, although you could always take a look at the Dahon (or Tern) website (including their archives) to see whether any of their bicycles have handlebars with more sweep; if so, then you might be able to contact them about ordering just the handlebars themselves. Alternatively, you could check with other folding bike companies to see if they have handlebars with more sweep and the same ridges. MEC (the REI equivalent on this side of the border) has their own folding bikes (rebranded Terns) and sells some replacement parts for them, so if REI also sells folders then you might be able to get inexpensive replacement handlebars from them.

Having said that, I think there's two things you really need to consider here: (1) putting handlebars with more sweep on them is going to take up more space when folded, especially on a Dahon that folds with the handlebars between the two halves of the bike, which may make for a bulkier package overall; and (2) you will exert more torque at the clamp using handlebars with more sweep if you lean against the handlebars while riding.

When it comes to (1), you can deal with that by pulling the stem off the bike or rotating the handlebars when folding it, assuming you've got enough slack in your cables. However, (2) becomes an issue with the quick-release clamp, as I don't think you can get quite the same clamping force as you do with a standard stem; thus, without the ridges, you can't clamp onto the handlebars with enough force to resist the torquing effect of pushing on the ends of the handlebars, thus causing the rotation. I'm sure you could really cinch down the quick release clamp, but my concern is that it would cause premature wear on the mechanism and it would quickly fail. You could also replace the quick release clamp lever with a bolt, but then you have more of an issue with (1) unless you remove your handlebars and stem every time you fold it.

As for possible solutions (assuming you can't find bars that have the grooves/ridges): you could try putting grooves in the handlebars yourself, using a milling machine, angle grinder, dremel, etc. You could also try roughing up the surface where the clamp goes with some low grit sandpaper or a wire wheel or something. You could also replace the quick release lever on the clamp with a bolt, although that would prevent you from being able to rotate the handlebars for folding, and may necessitate removing the stem and handlebars altogether when folding to get a nice compact package. Alternatively, you could get a standard handlebar stem and clamp that onto your existing stem/riser, just below the clamp, and use that instead; again, this still has the same issue with possibly having to remove the handlebars and stem/riser when folding, and it'll move your handlebars forward slightly (which may or may not be good for you), although it will allow you to properly torque down and use any handlebars you like. This standard stem is actually what I went with on my Speed P8, as I like a little bit more stretch and a little lower riding position than the standard setup offered.

I hope that help!
pope_face is offline  
Old 04-16-19, 12:30 PM
  #3  
linberl
Senior Member
Thread Starter
 
linberl's Avatar
 
Join Date: Jun 2014
Location: SF Bay Area
Posts: 3,064

Bikes: 2017 Bike Friday PakiT. Dahon Mu Uno (trailer bike) Sold: 2003 Bike Friday NWT, 1997 Trek 720, 1993 Trek 520)

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1189 Post(s)
Liked 177 Times in 148 Posts
Thanks. I've never seen bars with these kind of ridges before.
linberl is offline  
Old 04-16-19, 02:33 PM
  #4  
cocoabeachcrab 
Myrtle Beach Crab
 
cocoabeachcrab's Avatar
 
Join Date: Nov 2012
Location: Newport RI
Posts: 423

Bikes: enough one would think, but thinking isn't my strong point

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 144 Post(s)
Liked 148 Times in 72 Posts
have you tried tightening the quick release lever?
cocoabeachcrab is offline  
Old 04-16-19, 05:16 PM
  #5  
linberl
Senior Member
Thread Starter
 
linberl's Avatar
 
Join Date: Jun 2014
Location: SF Bay Area
Posts: 3,064

Bikes: 2017 Bike Friday PakiT. Dahon Mu Uno (trailer bike) Sold: 2003 Bike Friday NWT, 1997 Trek 720, 1993 Trek 520)

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1189 Post(s)
Liked 177 Times in 148 Posts
Originally Posted by cocoabeachcrab View Post
have you tried tightening the quick release lever?
Yeah. If I crank it down as hard as I can, it still doesn't hold when I stand and pump. There's a reason it has those deep ridges, I guess, to mate with the clamp. I just thought if Dahon make it this way, they'd offer some bar options.
linberl is offline  
Old 04-16-19, 05:23 PM
  #6  
cocoabeachcrab 
Myrtle Beach Crab
 
cocoabeachcrab's Avatar
 
Join Date: Nov 2012
Location: Newport RI
Posts: 423

Bikes: enough one would think, but thinking isn't my strong point

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 144 Post(s)
Liked 148 Times in 72 Posts
velo orange has some 25.4mm bars that have the serrations in the center for the clamp. i think.
cocoabeachcrab is offline  
Old 04-16-19, 07:23 PM
  #7  
linberl
Senior Member
Thread Starter
 
linberl's Avatar
 
Join Date: Jun 2014
Location: SF Bay Area
Posts: 3,064

Bikes: 2017 Bike Friday PakiT. Dahon Mu Uno (trailer bike) Sold: 2003 Bike Friday NWT, 1997 Trek 720, 1993 Trek 520)

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1189 Post(s)
Liked 177 Times in 148 Posts
Originally Posted by cocoabeachcrab View Post
velo orange has some 25.4mm bars that have the serrations in the center for the clamp. i think.
Yes, it looks like that in the pics!!! I've messaged them to make sure they are deep grooves and not just the typical light etching. Thank you so much for the tip! =)
linberl is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Silverexpress
Folding Bikes
51
04-28-20 07:40 AM
Tsujigiri00
Folding Bikes
56
04-17-17 03:10 PM
jyl
Folding Bikes
4
03-29-14 01:01 PM
5b00
Folding Bikes
7
11-08-13 08:17 PM
Veik
Folding Bikes
3
04-05-11 01:55 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.