PM Me.

ISO: mini velo frame

I guess these aren't really vintage but my best bet was here with the bigger audience. I know some consider them classic. Anyone have one of these little gems floating about with a rear dropout that has a derailleur hanger? Not the track drops. One that is a project...meaning just a frame or needing parts. Frame must be dent/ding and crack free. Examples would be Soma, Gios, Bianchi, Mercier...etc. I have vintage road bike and mountain bike frames I could trade and many other components. Other arrangements as well of course.. just PM me

ISO: women's brooks saddle for touring or similar. This is going to be a gift for my daughter so aesthetics are important.

Have: Campy Veloce 10s rd med cage vgc with 13-29 cassette. cassette has 50% left. Not a lot of wear on the teeth but the finish is , shall we say, cosmetically challenged.

record fd vgc edit: gone

orbea onix full carbon fork edit: gone

I believe I have what you're looking for. PM a example and and your other trade material. Not interested in the tri-color set.

ISO French threaded headset to replace my Stronglight P3. The P3 has a stack height of 33mm. Even just the top portion of the headset.

ISO Raleigh fork for my 23 1/2" or 58cm '77 Supercourse, looking to replace the plain steel I have with a better one in 531. I do not want a uni-crown style.

PM sent.

I need a derailleur cage spring for a Suntour Cyclone GT 1st generation. I'd rather not take a good derailleur apart but I'm willing to trade for a non-GT version. Or a complete GT. I can trade other derailleurs. Ideally one of you will have a busted RD and have been wondering what to do with it!

I have a few pre-cyclone GT RD's if you think the spring from one of those would work. By pre-cyclone, I mean the type that have the springs contained in a plastic housing with a screw holding the spring and housing to the body (like a seven series). If you think that RD would serve your needs, let me know.

Size?

oops, it is a 1977 and it is a 23 1/2" or 58cm

Thanks for the offer. I actually have one like that. Cursory inspection makes it look unlikely though. I tried springs from a VT and a VGT Luxe. They are all subtly different. The VT had half a millimeter smaller diameter so the pivot shaft wouldn't fit inside it. The VGT Luxe was the same diameter but two coils shorter so the anchor tab in the body wouldn't work. Little details like that...

Well, I have a 1st gen Cyclone with a busted spring in the bin, and I've been wondering what to do with it, but it doesn't sound like that's what you had in mind. Given the failure rate of those springs, replacements must have been available at some point.

You might find a suitable replacement at https://www.mcmaster.com/#compression-springs/=158ki5r

Interesting suggestion. We, i.e. other Cyclone owners and myself, actually need a torsion spring. McM have quite a few of those too. None have the rod directions we'd need but maybe just maybe that can be accommodated with judicious bending and cutting. Not by me with a pair of pliers though. Must ponder...

Did you email Yellow Jersey? They might have what you need.

Raleigh-threaded (26 tpi) bottom brackets (two sets of cups). I have a 1974 Competition and a 1949 Clubman that both don't seem to want to accept any of the bottom brackets that I have here.

Front derailleur. Clamp on for standard size English tubing for a mid 70's bicycle. Either a Sun Tour model or a Huret or Simplex would work. Used, but still presentable preferred.

Could also use six chainring bolts for a single ring. I hve an 8mm seat binder bolt that's 26mm long at the outside, about 22.5mm at the inside. I need an 8mm that's 4mm to 5mm shorter on the inside.

I have a plethora of assorted rear derailleurs, a few sets of brake calipers and some assorted bits for trade.

Wanted: Plastic cover for a Shimano bar-end shifter, 9-speed version in grey. Somehow and somewhere, the cover fell off of my right shift lever and I am looking for a replacement.

Which part do you need? The piece that goes over the end?

I've got a busted 8-speed lever that might work for you.

I just need the plastic cover that fits over the lever.

[MENTION=19743]USAZorro[/MENTION], I have your front derailleur. Email me.

PM me your address and I'll send what I've got out to you. It's an 8-speed lever (SL-BS64), but that part looks the same to me.

ISO: Brodie 2004 Hole Shot. Pretty much any workable condition.

Brodie Bikes <br /> <b>Warning</b>: include(../elements/bike_names/holeshot.php) [<a href='function.include'>function.include</a>]: failed to open stream: No such file or directory in <b>/raid/home/eyeplay/brodie/brodie/2016/archive/bike.php</b> on l

sent

May be a long shot but I am looking for a Cyclone M-II RD cable pinch bolt and allen head.

http://i1126.photobucket.com/albums/...d.jpg~original
http://i1126.photobucket.com/albums/...a.jpg~original
http://i1126.photobucket.com/albums/...g.jpg~original
http://i1126.photobucket.com/albums/...4.jpg~original