View Full Version : Framebuilders
- 30x17 chainstays questions
- Need Some Advice on O/A Regulators for a Beginner's Setup
- Longshen series 300 lugs
- What do you think of this frame damage (Reynolds 531)?
- Sandblasting + Powdercoating - How to make sure stamped VIN on BB is still legible?
- aluminum bike frame.
- Source for "Overdrive" bottom bracket shells?
- Stainless steel tubing: Strength vs stiffness
- Dream bike
- TIG vs Mig welding
- stuck seat post thread #99,182: The oversized seat post
- Frames made with Timetal 15-3 or 15-3-3-3 Titanium Tubing
- Please direct me to information about fork design
- Looking for a jig
- Looking for a frame builder to work with
- Looking for a specific frame
- french steel tubes
- Mongoose Seat Post Shear off
- Check my geometry please
- Best Modern Steel Tubing For Road Bike (columbus?)
- Newbie questions on ultra low cost frame building for pedgens in low income countries
- WTB Rear Campy drop-out (short)
- I need help with a rear dropout.....down and out in Los Angeles
- Carbon Fiber Tubes for Bicycle fraem building?
- steerer tube die pitch threading advice required.
- Is there a users guide to understand the difference in Frame Tube Sets
- Building frames as an occupation
- New steel for bikes?
- Spray Painting Mt Bike Frame with small Compressor advice needed.
- Prepping for paint-Sandblasting
- Gloss to Matte clearcoat?
- Is all double-butted 4130 created equally?
- Welding Recommendations
- Suggested tubing for first lugged steel frame build
- Need info on manipulating Aluminum for repair
- fork taper fabrication question
- Rebrazing arrachments on a front rack.
- Curvy geometry vs. straight geometry
- Using mild steel, will the frame collapse and kill me?
- Mondonico frame repair?
- question about unique touches i found on an NJS frame
- VERY slow-going build in process.
- S and S coupled Pinion drive frame
- Considering purchasing a New Steel Frame & Fork, any input on their frame builders?
- Carefully Straightening a Steel Seat Stay that's Dented and Bent
- New Framebuilder Website
- Ti or Al lug kits?
- Are any carbon fiber frame builders active on this forum?
- Need help with CAD drawing for new frame
- carbon frame life cycle and longevity
- Couple of frame questions- 80s steel frames specifically
- CS bridge length and gear cable adjuster boss questions
- Fork fail caught (just) in time - but how to repair?
- Small frame step through, chromoly, internal gear hub...
- Zona or Spirit for everyday + light touring
- Bottom HT lug
- Any frame builders here work @ Kinesis in the mid 90's?
- Integrated vs. Non-integrated seatpost clamp
- So I'm just about to finish my '71-'72 Peugeot build and...
- Dropout/Chainstay Repair
- Frame questions
- Both frames are 54cm, but 2 inch difference from fork to rear drop out.
- Touring Frame Question
- Converting a 1987 Cannondale Fork From Roller To Disc
- somebody build a frame, willya? This place is getting silly
- Artisan bikebuilding
- Slotting cable guides?
- Water Bottle boss problem
- Bent fork with 531c tubing - Reset to proper dimensions?
- Early frame dimensions
- First road bike build
- Screw and Glue (Epoxy) to build a frame?
- NY framebuilder to add rear disc tab on steel mtn frame?
- Can someone school me on steel as a material for making frames?
- How to remove a w/b boss, on the inside of tube?
- Trailer wheel mounts for 9mm QR wheels
- Best abrasives to clean up brass from brazed frame
- Lugged bottom bracket shells and chainstay angle
- Shorting the chainstays on an aluminum/carbon frame
- I bought serotta... Sorta
- Steel Ride and flex qualities equivalent in a Titanium frame?
- Dropout repair (rear) opinions
- Framebuilder Supply: Anyone have experience with these guys?
- bike frame wisdom: what i got vs. the new Rivendell
- Hammill fork bender - 8" madrel
- Jig Use
- What I saw at NAHBS 2015
- Bay area beginner, just trying to see what the story is out here.
- Chromoly 4130 Tube Sizes???? Bending????
- JIGLESS kit and method
- Is this frame salvageable?
- Frame with Overhead Bar(s)
- Length of intersection between down tube and top tube...
- Front dérailleur hanger opinion
- Is this aluminum frame normal?
- Star Bike Frame. Need advice for newbie
- Fork Blades for Small Wheels?
- Carrera Virtuoso 2002 LTD Edition DECALS
- Drafting, CADing, building
- Fork question