- Shimano 105 compatible with SRAM crankset?
- I feel like I am ridding in the mud
- 1 inch threadless stem where to find one
- Derailleurs
- Ding in rim - can I save this rim?
- My Giant Seek 1 chain keeps coming off when I switch gears?
- Does the middle chainring require ramps and pins?
- Shimano 105 (5500) freehub & 8-speed cassette compatibility?
- Chain Lube
- Sturmey-Archer restoration help
- 8 speed freewheel on spare rim
- Shimano UN-55 Bottom Bracket problems
- new headraces
- Asymetrical rear triangle cause chain skipping?
- Two Locknuts on the freewheel side?
- Spokes keep coming loose
- Installing Shimano 7610 BB
- crank and BB installation torque: does it really matter?
- Tektro Auriga Pro noise/vibration
- Trek 1200 STI Conversion - shift boss cable stop adapter part question?
- Front cable hangar--do I need the pipe?
- Rear Derailleur Chain Rub
- Time for a new tire?
- Shifters (Sora in this case) and short fingers
- Switching out Crank?
- can Tiagra hub spacing be increased to 135mm?
- bar end pod removal
- Crankset Swap Questions
- Converting MTN hubs to road hubs
- Soldering aluminum
- Buying a used slightly dinged frame? steel, chrome bianchi.
- Ultra Torque Crank In Swiss Thread Frame?
- Converting Sugino AT triple crank to index shifting
- creaking noise after installing new pedals
- How far to position clamp-on cable stop for bar-cons?
- Arg... missing bottom clamp section of my Pinarello seat rail clamp...
- Tools
- How to replace a threadless bottom bracket on this old tandem
- What is the tool to adjust XTR 900 rear hub?
- Proper tire width
- What do you think about this dent?
- Should I use loctite on my spokes ... after the build?
- Simple Question - Bike Chain
- Loosening up a stuck quill stem on an early '70s Raleigh Record
- Wheel building data: Weinmann 27" LP18 & Origin-8 sealed bearing front track hub.
- any tips on cleaning up road caliper brakes?
- 9 speed Shimano cassette on 7 speed hub with Campagnolo shifters...possible?
- Mountainbike fork swap for touring
- Can I convert my 27"x1-3/8" wheels to 26x?" wheels?
- Flat Bar Bar End Shifter Adapter????
- Modernizing my vintage peugeot?
- Use Brifter (Integrated Brake/Shifter) In Friction Mode?
- Bent Fork???
- Thin sleeve with carbon fork expansion plug
- problem with my hurricane team floor pump
- wheel off kilter, how do I fix? picture included
- Replacement for Campy 9 speed?
- Loud/Annoying Creaking coming from Headset or front end of my bike
- Same spoke every time?
- Hybrid suspension fork - what can I replace it with?
- With lower end low spoke count wheels, what is the best truing procedure?
- 700Cx35 on 14mm rim
- Why is butt welding ok now?
- Skipping under power
- Corrosion inside the frame?
- Stubborn bottom bracket
- How to remove this side-mounted hub?
- New bike serviced
- Stem a tight fit , is it allright ?
- Pedal Quality and Importance
- wet weather chain slip
- Looking to upgrade a Suntour x-1 set
- I want to build a rear wheel. Suggestions, info, anyone?
- In need of integrated headset help - Felt MTB
- Ultegra shifters are a little lazy in the middle of the range...
- Too short a chain?
- Chain too long?
- Shimano 105 5600 compatible with double?
- chain goes ka-chunk!!
- inner tube exploded
- Trek 7500 crank bearing advice needed
- Bontrager tire question for you tire guys?
- Replacing mtb tires with road friendly tires
- Brake quick-release for side-pull?
- Is this repairable? CAAD10 bent/dented seat stays
- Cannondale Synapse Carbon seatpost - better option?
- After washing/lubing chain, grinding noise. Help!
- HG 27tooth cogs prior to the 9speed
- Need HELP on handlebars bolt
- Veloce 9 speed shifting technique
- Replacement Crank for Bianchi Eros
- Dented untrued rear wheel
- Got a new bike in a box, should i build it myself or go to a LBS?
- a question on fork length
- Want to keep my BB, but need a new crank. Compatability suggestions?
- Differences between steel and aluminum frames
- Bike weight vs body weight
- Grrrrr!! Frustration over shifting
- Upgrading an old Raleigh Record. Possible? Worth the trouble?
- Drill holes for new rivet nuts?