- univega custom maxima shifter trouble
- One Key Release?
- Dura Ace RD 7800 rear derailleur
- Cannonondale DL 80 HeadShok ( Question )
- Presta tube in schrader rim?
- Spoke tension for GL330?
- Wet disk brake squeal.
- hard to remove cable guides. Trick?
- Extending brake drop options?
- Trigger shifter to road derailleur compatability
- Bike Size?
- V Brake levers
- Too stiff?
- advice needed
- Tubular tires and rim tape
- RD-4500 and FD-4500
- 3 speed Sturmey Archer help
- Ultegra Chainring
- replacing fixed gear 26" wheels with multi-gear 32" wheels
- Using a Touring fork on a CX bike.
- Question about removing anodization from rims?
- Tire Pressure
- Why would the chain be rubbing on crank?
- MTB to Commuter all around utility bike
- Cotter removed easily--crank won't budge!
- Strange bottom bracket
- Completely Repainting Bike
- Replacing a Tricross frame with a Pake C'mute frame
- Are there any road brakes that take wide tires?
- Did I Miss Something Regarding This Forum?
- Help! 10mm allen key don't fit freehub
- Why are derailleur hanger's made of aluminum?
- Does rust beget rust and the removal of rust spots on a bike
- v-brake noodle liner - necessary?
- do I have to disconnect the brake when removing front wheel?
- Aluminum Corrosion--Ouchies--Is this frame ok to ride??
- Find This Part..
- Rear Spacing Question
- Seat Post 26.8 -vs- 27.2 Thud Buster
- What do I need to do for this parts swap? (105 5700 triple to compact double)
- High Speed Wobble Cause?
- Do old wheels decrease braking efficiency?
- Installing old-school Scott aerobars
- Choosing the correct rear d�railleur?
- Is all epoxy the same? Cracked seat tube.
- Problem with SKF bottom bracket
- Drilling my steer tube and/or stem?
- Aluminum Cannondales
- Two questions about tubes.
- bike storage hook
- Can I use these Kool Stops for my Tektro brakes?
- Front cantilever brake cable routing?
- Suntour XCR650 rear mech - design issues?
- what is the best way to pop off the rivet holding a headtube badge on?
- Adapt internal hub to take 9-spline cog?
- Does anyone know the torque rating of single speed freewheels?
- Component Installation Pricing?
- Vintage decals
- Crossed shifter cables??
- Wheelset upgrade for the layman
- Bullhorns work with this bike?
- Any easy way to crack open a Speedplay 'Frog' pedal?
- american classic 420 which non-ceramic bearings?
- Tube sizes????
- Chain slips on every rotation
- Kool Stop Eagle 2
- Tricks for removing rusted on Pedals
- Are seatstay bridges all drilled the same?
- unable to raise seat on cruiser bike?
- Help! My BB30 bearings are driving me insane.
- Newbie not smart enough to operate a floor pump
- Is Freewheel format dead? Looking for >7spd freewheels
- Ovalized Bottom Bracket, it is fixable?
- Looking for a extra long 5mm hex key...cheap.
- Suntour XCR fork knocks when locked
- disc brake pads have plenty of mat'l left, but are faded out
- Time to replace headset?
- Integrated Headset Installation Help
- Early 90s Deore LX rear hub spacing?
- how to tell if a bike is truly single speed?
- Brooks B67 tension adjustment
- disc hub wheel compatibility
- Chain comes loose if I don't pedal
- "Full Speed Ahead" Cranksets Recalled
- Bent Chainring
- park ct11 and ct4.2 viable alternative to the campy tool?
- wipperman connex 108 "whitestar" chain and quick link
- bunch of questions
- Rear Derailleur adjustment question
- possible to use front shift lever for rear deraileur?
- after replacing a bike's tubing how to replace the tire? this always gets me
- Tough Road tire ... getting a tight wire bead over the rim
- Mixing Campy Comnponents
- Jagwire BarCon 2.0 vs. Rivendell Shift Pods (DT to bar end shift)
- Rear shifter not working after fitting new gear cable
- Austro Daimler HEADSET
- Stupid Truvativ Elita GXP left crank keeps getting loose
- Shimano 105 Pedal - Toe Clip
- Can riding up a steep slope break the chain?
- mountain bike tire tubing = cruiser bike tire tubing?