View Full Version : Bicycle Mechanics
- Giant ARX2 front & rear shifting issues
- Best rims for a 1981 Raleigh Reliant (27 x 1 ¼)?
- How much hop at the joint in the rim is acceptable?
- Freehub Identification
- Not sure how to remove this cassette
- Changing Sram Rival 1 chainrings
- Chain ring all bent up
- If I have to stand on a 30 cm BB wrench and jump to get BB off, is torque too high?
- Cassettes
- Any JIS threaded headsets with <38mm stack height?
- How to measure chainring width?
- Can't properly adjust linear brakes
- Tight cassette
- Can I convert to a Fixed
- Uncentered Wheel Safety?
- need recommendation for front hub build
- Road bike involved in small crash: What to do next?
- Tektro flat bar V brake lever barrel adjuster
- 1 ring up front 5 speed freewheel out back , 9 speed chain
- Brand new wheel creaky freehub body
- Mavic XA elite hub does not engage
- Shimano 105 - 5800 Crankset
- Campagnolo RD shifting problems
- Double derailleur for triple crankset
- Can I use this rear der with my bike?
- Front wheel on backwards?
- On custom 'cycle wheel hubs
- 9 Speed Trigger Shifters??
- 6402 Freehub play
- BB386EVO crankset compatible with CK ThreadFit 30 BB?
- Shimano BR-550 brakes
- Changing sprockets on a 10 speed?
- Campag compatibility for cross frakenvike (magura/shimano)
- Do I Need To Worry About This BB Going Away?
- What crank did a Trek 7000 from 1990 have?
- Shimano SIS SP (not SP41) cable housing pre-lubed?
- Bottom bracket query
- Axle components
- Crank Removal - Single Speed Track, 46T
- Best Disc Pads
- When my rear wheel slows down, it starts going the in opposite direction
- Looking for larger fly wheel
- SRAM 10 speed front lever compatibility...
- New Drivetrain/Bad Chainline Problem
- How bad is this? Cracked crank arm
- Freewheel Disappointment....Wahhhhhh
- Trouble with longboards
- 9 speed Campy Daytona doesn't shift to largest cog.
- Sachs Centera rear long cage derailleur
- Smaller Quill stem
- Ultegra Di2 groupset with Deore XT Di2 shifters
- Frozen stem and handlebar clamp
- Hidden vs non-hidden bolt crank
- Big chainring trim click disappeared
- SRAM 11 and 10-speed RD backwards compatibility
- Suggestions on Trek Madone 7 build
- Lacing from wheel that was built not symmetric, should I flip one side?
- Frame/component detailing
- Is this damage repairable
- Replacing front rigid with suspension
- Brake comparison
- What taught you the most about bicycle mechanics?
- Older Tires, Any Use Concerns?
- Centering Chorus Monoplanar Calipers
- Specialized Amira OSBB- Shimano crank install
- PF30 bracket to ultegra 8000 crank
- Bottom bracket upgrade compadibility
- Strange problem shufting help
- Old Sturmey Archer 3-speed hub. Is this a fault?
- Narrow-wide 1x chanrings for new Shimano cranks?
- Need to disconnect hydro hose. Need a new olive?
- Help ID suspension fork for kids bike
- Campagnolo Record Strada Bottom Brackets
- A Tire Question
- Rice Krispy drivetrain
- chain/cassette question
- Replacing inner chain ring for lower granny gear
- Reuse Shimano BB86
- Shimano 3 spd hub dropout fitment
- 28T chainring for 1 x 9, or bigger biggest cog , possible ?
- Tube Change Question (out of round after change)
- FSA chain ring replacement
- Road vs MTB Disc Rotors
- Suspension so stiff, have tried oiling and everything
- SRAM PC-991, Molten Speed Wax drivetrain conversion
- Embedded metal bits in cartridge brake pads, what to do?
- Replacement Bottom Bracket
- Replacing one shifter or all components on a 1995 Cannondale?
- Kestrel 200SCI threaded headset issue
- Looking for a CO2 Inflator for 16G NON-Threaded Cartridges
- Compatibility of Shimano Sora 8-Speed RL-400 Downtube Shifters
- Sram Chains-Grey &Silver
- 10-speed chain on older drivetrains
- New tyres are a bit warped. Is this bad?
- Seat post completely slipping due to cracked bike tube - Options?
- List of Shimano derailleurs
- Adjusting Hydraulic brake levers
- Front Derailleur cable tension
- Where is the wear limit on my brake pad?
- Adding a B-Screw to a Shimano Deerhead