- Shimano HB-M475
- front fork vibration when braking
- [FWD] Recumbent w/ Belt Drive
- [FWD] Recumbent w/ Belt Drive
- Chain rubs on front derailleur
- Anti-seize Compounds
- Not in love with Campy brake setup, please help!
- Can I lace a 24h to a 32h hub?
- Do Shimano 7801 chain pins work with 7900 chains?
- Gear slipping
- Disc rim with V-brakes?
- SRAM S7 push rod lenght ?
- Shimano RD puley, bushings vs. sealed bearings. Are different models interchangeable?
- Rust removal techniques
- Cone Conundrum Continues, advice needed!!!
- Campy BB30 Adapter Question
- Which headsets fit a Cannondale Trail SL 5 ?
- Threaded to Threadless Fork Steerer Length?
- Revised Campy Khamsin 2011 wheelset?
- Tire problem - What do you think caused it?
- Teflon Tape vs. Grease on Threads
- Trashed Front Derailer
- Built to fail?
- Powertap head won't find hub after firmware upgrade
- Cranks spin forward without catching and chain not moving
- new wheels, chain slipping on cassette?
- Cone compatiability in old Formula (MTB) Hubs from 90s
- Centering cheap cantilever brakes?
- Where do I start?
- Giante Revive
- Single speed question
- Pedro's or Park Cable Cutter?
- Cassette options
- Crank length 170mm, 172.5mm, 175mm
- Bottom Bracket Replacement on Trek Soho S
- Convert Octalink V1 to Hollowtech II for a Dura-Ace 7900 crank
- Convert my Kestrel threaded 1" quill stem to threadless
- Fork rake questions
- Ultegra 6600 short cage RD on a 34/50 -11/28 setup
- I meant what size FD clamp?
- The pedals fell off my bike - not how you think; please help
- What size FD?
- SRAM Quick Link & DA 9 sp Chain
- Shimano 3 speed coaster hub cable replacement.
- Schwinn Seatpost Question
- crankset recommendation
- 1978 Campagnolo New Record Crank Spindle Replacement
- Brake and drivetrain issues?
- Axle mounted kickstand instructions
- Two specialized city bikes (Hard rock & Rockhopper) canti-lever issues.
- Correct BB for Ultegra SL 6600 cranks going into Defy Advanced frame?
- Can I mount a brake here?
- Replacing Bearings in Campagnolo Cartridge BB
- Shimano 6700 vs 6701 chain?
- Brifter dead?
- Headset Choice
- Ultegra Crankset
- New bike!!!
- Reasonably Accurate Low End Vernier Calipers?
- Rear brake makes a "thump" 1x per revolution
- switching pedals and brakes on a ''CX'' bike
- modifying a rear mountain bike hub
- New V-Brakes - Is vertical alignment a rule of thumb or a functional issue?
- crankset help... stripped female threads for grannie ring
- Pedaling won't move the tires.
- Campy help! Need to replace cone in 8 speed Chorus rear hub- part availablity?
- Front derailleur issue
- Bottom Bracket came loose?
- Are spacers above the stem necessary?
- Is Shimano 9 speed jockey wheels OK with eight speed drivetrain.
- Problem: jammed BBB Roundhead extender
- Sluggish cassette up shift
- what size pin spanner?
- 44T front derailleur with 48T (M771 MTB)
- seat keeps slipping down roughly half an inch
- is this wheel unrepairable? Mavic Cosmic
- Look Keo axle/bearing problems
- Substituting a 34 in place of a 36 tooth middle chainring on a MTB
- What books are you reading/have you read that you found informative?
- Sealed Bearing Hub Rusted Stuck
- Bottom Bracket Replacement
- Old school stem, new school handlebar
- I need help fine tuning my front derailleur
- upholstering a saddle
- Steerer length rule of thumb?
- 7-speed cass on 8/9 speed wheel on old Raleigh
- Road Caliper Brakes on MTB bridge
- Problem: replacement triple crank too close to frame?
- storing tools and parts without drawers or pegbboard
- Converting Road pads for Cantis
- Rear Axle Type: 10x1
- External bottom bracket <--> cranks
- Help, with hubs....
- Tools.......buy as you need, or get a 'kit'?
- 9 speed to 10 speed conversion
- 1984 Peugeot UO-14
- Carbon or aluminum steerer on carbon fork?
- Can't tighten OR loosen my stem/bar bolt.
- New front brake cable feels (and sounds) like a zipper
- Help removing old crank